Sponsored Content
Operating Systems Linux Red Hat Regarding Network Interface Card Post 302919407 by gull04 on Wednesday 1st of October 2014 05:55:24 AM
Old 10-01-2014
Hi,

This could be down to several things, firstly a couple of questions.

First, what version of Netbackup.
Second, was the error on the Client or the Server.
Third, how much data - I think in some older versions these type of errors were due to size.
Fourth, what is being backed up and how - is it NDMP etc.

The more information that you provide, the better the chance that someone will be able to assist you.

Regards

Dave

Last edited by gull04; 10-01-2014 at 06:55 AM.. Reason: Typo
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

2. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

5. Solaris

Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem, but how do you troubleshoot this issue? How can I find out which connections are made for one interface card, there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies

6. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

8. Red Hat

Interface card link goes down and recovers frequently

Hi Experts, I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back. 2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down 2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
TR(4)							   BSD Kernel Interfaces Manual 						     TR(4)

NAME
tr -- TROPIC based shared memory Token-Ring cards device driver SYNOPSIS
tr0 at isa? port 0xa20 iomem 0xd800 irq ? tr* at isa? port ? irq ? tr* at isapnp? tr* at mca? slot ? tr* at pcmcia? function ? DESCRIPTION
The tr device driver supports TROPIC I based shared-memory Token-Ring cards. HARDWARE
Supported cards include the following IBM and 3Com models: IBM Token-Ring Network PC Adapter IBM Token-Ring Network PC Adapter II IBM Token-Ring Network Adapter/A IBM Token-Ring Network 16/4 Adapter IBM Token-Ring Network 16/4 Adapter/A IBM Token-Ring 16/4 Credit Card Adapter IBM Token Ring Auto 16/4 Credit Card Adapter IBM Turbo 16/4 Token Ring PC Card IBM 16/4 ISA Adapter IBM Auto 16/4 Token-Ring ISA Adapter IBM Token Ring 16/4 Credit Card Adapter IBM Token Ring Auto 16/4 Credit Card Adapter IBM Turbo 16/4 Token Ring PC Card 3Com 3C619 TokenLink 3Com 3C319 TokenLink Velocity 3Com 3C389 TokenLink Velocity PC Card SOURCE ROUTING
Setting IFF_LINK0 enables Token-Ring source routing. Setting IFF_LINK1 uses all-routes broadcasts otherwise single-route broadcasts are used. NOTES
The MCA attachment has been only tested on IBM Token Ring 16/4 Adapter/A so far. It doesn't support ifmedia(4) yet, too. SEE ALSO
ifmedia(4), intro(4), isa(4), isapnp(4), mca(4), pcmcia(4), ifconfig(8) HISTORY
The tr driver appeared in NetBSD 1.4. BUGS
The PCMCIA attachment does not work with the cbb(4) CardBus driver. BSD
April 14, 1999 BSD
All times are GMT -4. The time now is 10:01 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy