Hi,
Tried to look for solution, and found something similar but could not adapt the solution for my needs..
I'm trying to match a pattern (in this case "ProcessType")in a logfile, then delete that line and the 4 following lines.
The logfile looks as follows:
ProcessType: PROCESS_A... (5 Replies)
I want to write a scrpit to merge files row wise (actually concatinating)
main.txt
X Y Z
file 1
A B C
file 2
1 2 3
now i want the script to check if the file1 is empty or not, if empty then make it like
A B C
1 2 3
again to check if second file is empty if not do as done... (0 Replies)
Dear all,
I have been trying to print an entire field, if the first line of the field is matching.
For example, my input looks something like this.
aaa ddd zzz
123 987 126
24 0.650 985
354 9864 0.32
0.333 4324 000
I am looking for a pattern,... (5 Replies)
Hi Friends,
I have a single column data like below.
1
2
3
4
5
I need the output like below.
0
1
2
3
4
where each row (including first row) subtracting from first row and the result should print below like the way shown in output file.
Thanks
Sid (11 Replies)
Hello all,
this is my first and probably not my last question around here. I do hope you can help or at least point me in the right direction.
My question is as follows, I need to find files and possible folders which are not owner = AAA group = BBB with a said location and all sub folders ... (7 Replies)
First I'd like to apologize if I opened a thread which is already open somewhere.
I did a bit of searching but could quite find what I was looking for, so I will try to explaing what I need.
I'm writing a script on our server, got to a point where I have two files with results. Example:
File1... (6 Replies)
Using the awk below I am able to combine all the matching dates in $1, but I can not seem to remove the non-matching from the file. Thank you :).
file
20161109104500.0+0000,x,5631
20161109104500.0+0000,y,2
20161109104500.0+0000,z,2
20161109104500.0+0000,a,4117... (3 Replies)
Discussion started by: cmccabe
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)