I would say you have an extra PCI card with two network interfaces in your system.
Check the device pathes to your NICs in /etc/path_to_inst and see if one of the onboard devices is e1000g2. Here is a list of the onboard NIC device path:
I need to configure the iLOM for x4600 server. before I can set the IP details and commit, I need to set network state should be enabled. However my firmware is already the latest and I need not upgrade. I am not able to set the /SP/network state to enable. pls assist. i BELIEVE the bug was fixed... (5 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi Folks,
Has anyone seen these errors on bootup.
Mar 15 12:22:30 svc.startd: svc:/system/device/local:default: Method "/lib/svc/method/devices-local" failed due to signal SEGV.ht (c) 1983, 2010,
Oracle and/or its affiliates. All rights reserved.
Configuring devices. ... (1 Reply)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
I got a replacement Heatsink and Fan unit, but the OEM unit has the SUN Thermal Interface Material (TIM) already on the heatsink matting surface. Because mine is used it does not have the TIM. Also there are 2 different TIM material SUN used based on the Processor (1-1.28GHz uses a glue backed... (1 Reply)
Booting and checking BIOS there is no option to enable-disable hyperthreading.
I have 8 Dual-Core AMD Opteron(tm) Processor 8220 and I see 16 cores.
Enable hyperthreading I should have 32 cores.
I have red hat 5.4 installed.
Anyone know how can enable hypethreading ? I have last BIOS/Firmware... (2 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT NETBSD
virtio
VIRTIO(4) BSD Kernel Interfaces Manual VIRTIO(4)NAME
virtio -- Para-virtualized I/O in a virtual machine
SYNOPSIS
virtio* at pci? dev ? function ?
ld* at virtio?
vioif* at virtio?
viomb* at virtio?
DESCRIPTION
virtio defines an interface for efficient, standard and extensible I/O between the hypervisor and the virtual machine. The virtio device
driver represents an emulated PCI device that the hypervisor makes available to the virtual machine.
virtio driver itself provides the core infrastructure to communicate with the hypervisor (called virtqueues) and supports the following
devices:
ld(4) A Disk device.
vioif(4)
An Ethernet device.
viomb(4)
A pseudo-device to release memory back to the hypervisor.
SEE ALSO ld(4), pci(4), vioif(4), viomb(4)
Rusty Russell, IBM Corporation, Virtio PCI Card Specification, http://ozlabs.org/~rusty/virtio-spec/.
HISTORY
The virtio driver first appeared in NetBSD 6.0.
BSD November 5, 2011 BSD