Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
SHAME, that's all that I'm felling right now, however I'm not finding PING or either tracert in my box (Solaris 10).
1) Yes my PATH does have /usr/bin /usr/sbin
# echo $PATH
/opt/csw:/usr/bin:/sbin:/usr/sbin:/usr/ccs/bin:/usr/sfw/bin:/opt/csw/bin:/opt/csw/gcc2/bin:/opt/csw/bin
2) If I... (1 Reply)
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
This is a small program as a tester for a basic sweep generator for bandwidth testing of AudioScope.sh.
This DEMO is only capable of 4KHz down to about 85Hz and back due to the low bit rate, but it is proof of concept for a much wider variant using a much higher bit rate.
The file generated... (4 Replies)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
control_rancid
control_rancid(1) General Commands Manual control_rancid(1)NAME
control_rancid - run rancid for devices of a group
SYNOPSIS
control_rancid [-V] [-m mail_rcpt] [-r device_name] group
DESCRIPTION
control_rancid is a sh(1) script to parse a group's router.db(5), run rancid for each of the devices, possibly re-run rancid for devices
that failed collection, e-mail diffs, and e-mail error reports.
The command-line options are as follows:
-V Prints package name and version strings.
-m mail_rcpt
Specify the recipient of diff mail, which is normally rancid-<group>. The argument may be a single address, multiple comma
separated addresses, or -m may be specified multiple times.
-r device_name
Specify the name, as it appears in the router.db, of a particular device to collect and generate diffs for. The device must be
marked "up".
The -r option alters the subject line of the diff mail. It will begin with <group name>/<device name> rather than just the group
name alone.
control_rancid is normally (and best) run via rancid-run(1) which provides a locking mechanism on a group basis and saves output in a log
file for each group.
SEE ALSO rancid-run(1), rancid.conf(5), router.db(5)
5 October 2006 control_rancid(1)