02-04-2014
telnet on solaris is disabled by default, to enable it you must use svcadm command
as root issue
svcadm enable telnet
Be aware that telnet is non-secure application, everyone can listen your traffic. Use SSH instead. If your Solaris box doesn't have IPFilter enabled than all ports should be accessible.
To be sure, try to pause firewall using following command
svcadm disable ipf
9 More Discussions You Might Find Interesting
1. Programming
i have made some thing with leds on it. i put it directly on the printer port. in dos and windows i can send data to it with outp(0x378,123); and then have some leds on and some leds off. i found out that it is possible linux with same assembly (after searching much.). but i want to have those led... (0 Replies)
Discussion started by: jurrien
0 Replies
2. Solaris
hi all,
My OS is solaris 8 with core system installation only. so far everything works fine. by i do some testing from my xp pc as client to nmap and scan opening port to my solaris. the result as below:
Initiating SYN Stealth Scan against 10.10.10.10 at 16:25
Discovered open port 21/tcp on... (3 Replies)
Discussion started by: hezry79
3 Replies
3. Linux
How can I open a port on linux machine ??? (5 Replies)
Discussion started by: mm00123
5 Replies
4. IP Networking
Hi. I ran nmap on my server, and I get the following:
Starting Nmap 4.76 ( http://nmap.org ) at 2009-03-19 16:33 EDT
Interesting ports on -------- (-----):
Not shown: 997 closed ports
PORT STATE SERVICE
22/tcp open ssh
80/tcp open http
6881/tcp open bittorrent-tracker
The... (0 Replies)
Discussion started by: Rledley
0 Replies
5. Solaris
Unable to open 3966 port for buildforge in Solaris 10, anyone pls help me how to open the 3966 port in solaris.
Thanks in Advance (1 Reply)
Discussion started by: durgaprasadr13
1 Replies
6. Solaris
Hello guys,
I've recentrly installed a Tomcat server in our Solaris 8 servers, and while it's properly configured and running already, I can't access the port from outside the network segment the server is on.
I.e., we have 4 servers in the same segment (consecutive IP addresses), and if I... (4 Replies)
Discussion started by: Acapulco
4 Replies
7. Solaris
Hi All,
I am installing Infosphere (ETL tool) on solaris 10.
One of the requirement is to open multiple ports for different apps that will be installed. I ran netstat -n | grep 9080 (,etc) but that did not return anything.
I have attached the requirement. Can anyone guide me about how to... (3 Replies)
Discussion started by: sumeet
3 Replies
8. Solaris
Hi there,
I'm sorry in advance if my question seems stupid, but I can't figure out myself.
I was wondering. Is it possible to install a Solaris program on an Open Solaris or Open Indiana operating system?
After searching the web for a long time, it seems that Open Solaris was released by... (7 Replies)
Discussion started by: firstpost
7 Replies
9. IP Networking
i want to kill a tcp connection by killing its pid
with netstat -an i got the tcp ip connection on port 5914
but when i type ps -a or ps-e there is not such process running on port 5914
is it possible that because i do not log on with proper user account i can not see that process running? (30 Replies)
Discussion started by: alinamadchian
30 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)
NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS
--predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO
bup-midx(1), bup-save(1)
BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown- bup-margin(1)