12-02-2013
Telling us that filenames are something like
x-y where x and y are strings of digits isn't enough for us to figure out how to determine which file is file1, file2, ...
Give us details.
- How do you know which files are to be combined and in what order?
- Are the names of the files just two strings of digits separated by a single minus sign, or are the other characters in the name that need to be skipped over (or used to determine the order in which they're to be concatenated?
- How do you determine the output file name (or do you just want the output to be written to stout?
- Can we choose which shell we want to use, or have you decided the only one shell should be used? If only one, which one?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
:mad: I did this the other day but one of my support personnel removed my history so i could call it back up to remeber the exact command since i am air-headed at times. I am trying to take a 30 MEG file off the system and drop it to tape then i want to make the file go back to being 0 bytes so... (1 Reply)
Discussion started by: JackieRyan26
1 Replies
2. Shell Programming and Scripting
Hi all,
Does anybody know or guide me on how to remove the first N bytes and the last N bytes from a binary file? Is there any AWK or SED or any command that I can use to achieve this?
Your help is greatly appreciated!!
Best Regards,
Naveen. (1 Reply)
Discussion started by: naveendronavall
1 Replies
3. Shell Programming and Scripting
hi
My requirement is i have a file with some records like this
file name ::xyz
a=1
b=100,200
,300,400
,500,600
c=700,800
d=900
i want to change my file
a=1
b=100,200,300,400
c=700,800
d=900
if record starts with " , " that line should fallows the previous line.please give... (6 Replies)
Discussion started by: srivsn
6 Replies
4. UNIX for Dummies Questions & Answers
Hi,
How do I check for the total bytes of character used by a file?
Can I used a od command to check?
Thanks. (1 Reply)
Discussion started by: user50210
1 Replies
5. Programming
What is the easiest way to inspect the bytes stored in a file?
Ideally, If my file was 10 bytes each of which had only the high bit set, I'd be able to browse for it and get output like this:
01 - 10000000
02 - 10000000
03 - 10000000
04 - 10000000
05 - 10000000
06 - 10000000
07 -... (7 Replies)
Discussion started by: sneakyimp
7 Replies
6. Shell Programming and Scripting
While running script I am getting an error like
Few lines in data are not being processed.
After googling it I came to know that adding such line would give some memory to it
ini_set("memory_limit","64M");
my input file size is 1 GB.
Is that memory limit is based on RAM we have on... (1 Reply)
Discussion started by: elamurugu
1 Replies
7. Programming
Hi,
If I want to copy a 1024 byte data stream in to the target location in 3-bytes chunk, I guess I can use the following script.
dd bs=1024 count=3 if=/src of=/dest
But, I would like to know, how to do it via a C program. I have tried this with memcpy(), that did not help. (3 Replies)
Discussion started by: royalibrahim
3 Replies
8. UNIX for Dummies Questions & Answers
Hello guys. I really hope someone will help me with this one..
So, I have to write this script who:
- creates a file home/student/vmdisk of 10 mb
- formats that file to ext3
- mounts that partition to /mnt/partition
- creates a file /mnt/partition/data. In this file, there will... (1 Reply)
Discussion started by: razolo13
1 Replies
9. Shell Programming and Scripting
hello,
suppose, entered input is of 1-40 bytes, i need it to be converted to 40 bytes exactly.
example: if i have entered my name anywhere between 1-40 i want it to be stored with 40 bytes exactly.
enter your name:
donald duck (this is of 11 bytes)
expected is as below - display 11... (3 Replies)
Discussion started by: shravan.300
3 Replies
10. Shell Programming and Scripting
is there a better way to do this:
head -c 10000k /var/dump.log | head -c 6000k
unfortunately, the "-c" option is not available on sun solaris. so i'm looking at "dd". but i dont know how to use it to achieve the same exact goal as the above head command.
this needs to work on both solaris... (5 Replies)
Discussion started by: SkySmart
5 Replies
cat(1) User Commands cat(1)
NAME
cat - concatenate and display files
SYNOPSIS
cat [-nbsuvet] [file...]
DESCRIPTION
The cat utility reads each file in sequence and writes it on the standard output. Thus:
example% cat file
prints file on your terminal, and:
example% cat file1 file2 >file3
concatenates file1 and file2, and writes the results in file3. If no input file is given, cat reads from the standard input file.
OPTIONS
The following options are supported:
-n Precede each line output with its line number.
-b Number the lines, as -n, but omit the line numbers from blank lines.
-u The output is not buffered. (The default is buffered output.)
-s cat is silent about non-existent files.
-v Non-printing characters (with the exception of tabs, new-lines and form-feeds) are printed visibly. ASCII control characters
(octal 000 - 037) are printed as ^n, where n is the corresponding ASCII character in the range octal 100 - 137 (@, A, B, C, . . .,
X, Y, Z, [, , ], ^, and _); the DEL character (octal 0177) is printed ^?. Other non-printable characters are printed as M-x,
where x is the ASCII character specified by the low-order seven bits.
When used with the -v option, the following options may be used:
-e A $ character will be printed at the end of each line (prior to the new-line).
-t Tabs will be printed as ^I's and formfeeds to be printed as ^L's.
The -e and -t options are ignored if the -v option is not specified.
OPERANDS
The following operand is supported:
file A path name of an input file. If no file is specified, the standard input is used. If file is `-', cat will read from the
standard input at that point in the sequence. cat will not close and reopen standard input when it is referenced in this
way, but will accept multiple occurrences of `-' as file.
USAGE
See largefile(5) for the description of the behavior of cat when encountering files greater than or equal to 2 Gbyte ( 2**31 bytes).
EXAMPLES
Example 1: Concatenating a file
The following command:
example% cat myfile
writes the contents of the file myfile to standard output.
Example 2: Concatenating two files into one
The following command:
example% cat doc1 doc2 > doc.all
concatenates the files doc1 and doc2 and writes the result to doc.all.
Example 3: Concatenating two arbitrary pieces of input with a single invocation
The command:
example% cat start - middle - end > file
when standard input is a terminal, gets two arbitrary pieces of input from the terminal with a single invocation of cat. Note, however,
that if standard input is a regular file, this would be equivalent to the command:
cat start - middle /dev/null end > file
because the entire contents of the file would be consumed by cat the first time `-' was used as a file operand and an end-of-file condition
would be detected immediately when `-' was referenced the second time.
ENVIRONMENT VARIABLES
See environ(5) for descriptions of the following environment variables that affect the execution of cat: LANG, LC_ALL, LC_CTYPE, LC_MES-
SAGES, and NLSPATH.
EXIT STATUS
The following exit values are returned:
0 All input files were output successfully.
>0 An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|CSI |enabled |
+-----------------------------+-----------------------------+
|Interface Stability |Standard |
+-----------------------------+-----------------------------+
SEE ALSO
touch(1), attributes(5), environ(5), largefile(5), standards(5)
NOTES
Redirecting the output of cat onto one of the files being read will cause the loss of the data originally in the file being read. For exam-
ple,
example% cat filename1 filename2 >filename1
causes the original data in filename1 to be lost.
SunOS 5.10 1 Feb 1995 cat(1)