11-18-2013
As a note of explanation, this procedure applies only to host bus adapters, not RAID controllers such as the Mylex DAC960.
Also when the host bus adapter is changed, the new adapter may not see the drive with the same geometry, so it may be necessary to use the 'biosgeom' boot string, and then run 'dparam' to make the change permanently.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. IP Networking
I have 2 identical printers with the same IP on my network. One is only used as a backup for the primary printer and both are never on line at the same time. The goal was to always keep only 1 on and have an use the other printer as an immediate backup if necessary. But when I switch the cable I... (4 Replies)
Discussion started by: golfs4us
4 Replies
2. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
3. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
4. UNIX for Dummies Questions & Answers
Hello people i have a samba and they changed domain controller from a windows 2003 to a windows 2008, there is a problem with the version of samba maybe incompatibilities i dont know what show me this
domain_client_validate: unable to validate password for user xxxx in domain xxxx to Domain... (0 Replies)
Discussion started by: enkei17
0 Replies
5. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
8. IP Networking
Hi All,
I was told to perform analysis for IP change during a hardware refresh?
Does the IP change when a hardware refresh is performed?
if Yes, why? (5 Replies)
Discussion started by: visitsany
5 Replies
9. Linux
Hi Forum.
I have been searching this information for a while but to no avail.
I'm running the following command odbcinst -j on a Linux box and get the following:
unixODBC 2.3.0
DRIVERS............: //opt/Progress/DataDirect/Connect64_for_ODBC_71/odbcinst.ini
SYSTEM DATA SOURCES:... (2 Replies)
Discussion started by: pchang
2 Replies
10. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
ICP(4) BSD Kernel Interfaces Manual ICP(4)
NAME
icp -- ICP-Vortex and Intel Storage RAID driver
SYNOPSIS
icp* at pci? dev ? function ?
ld* at icp? unit ?
icpsp* at icp? unit ?
scsibus* at icpsp?
DESCRIPTION
The icp driver provides support for the newer (post 1997) ICP-Vortex GDT and Intel Storage RAID controllers.
The ld driver provides access to logical devices (disk arrays) presented by the controller. The icpsp driver provides direct access to other
SCSI devices attached to the controller, such as tape or CD-ROM drives.
DIAGNOSTICS
pci_mem_find: expected mem type 00000000, found 00000002
This message may be displayed during autoconfiguration if the controller's memory is mapped below 1MB in physical address
space. This can be disabled either through changing a setting in the controller's BIOS utility, or changing the position of a
jumper on the board. See your controller's documentation for more information.
SEE ALSO
intro(4), ld(4), scsi(4)
HISTORY
The icp driver first appeared in NetBSD 1.6, and was based on the FreeBSD and OpenBSD drivers of the same name.
BUGS
ISA & EISA front-ends and a management interface are needed.
Older PCI boards are not yet supported.
BSD
April 20, 2002 BSD