11-05-2013
You could create a new NIC for the Global and then assign it to the local.
I can't help with virtualbox, I've never used it before. But again, to my opinion, you need a device dedicated to your local to accomplish what you're describing.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (1 Reply)
Discussion started by: s_aamir
1 Replies
2. Cybersecurity
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (2 Replies)
Discussion started by: s_aamir
2 Replies
3. Solaris
Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
Discussion started by: DarReNz
5 Replies
4. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
5. Solaris
Hello all,
I`ve the following problem - I cannot start inetd in any way possible:
bash-3.00# svcs inetd
STATE STIME FMRI
offline Jul_30 svc:/network/inetd:default
bash-3.00#
bash-3.00# svcadm enable -r inetd
bash-3.00# svcs inetd
STATE STIME FMRI... (6 Replies)
Discussion started by: click
6 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
8. Solaris
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Discussion started by: amity
2 Replies
9. UNIX for Beginners Questions & Answers
I'm trying to migrate a Solaris 10 flar archive from a Sun M3000 to a T4-1. When I first created the zone I followed the Oracle instructions here: Transitioning an Oracle Solaris 10 Instance to an Oracle Solaris 11 System - Transitioning From Oracle Solaris 10 to Oracle Solaris 11 That worked... (6 Replies)
Discussion started by: Michele31416
6 Replies
LEARN ABOUT OPENDARWIN
zprint
ZPRINT(1) General Commands Manual ZPRINT(1)
NAME
zprint - show information about kernel zones
SYNOPSIS
zprint [-w] [-s] [-c] [-h] [name]
DESCRIPTION
zprint(1) displays data about Mach zones. By default, zprint will print out information about all Mach zones. If the optional name is
specified, zprint will print information about each zone for which name is a substring of the zone's name.
zprint interprets the following options:
-w For each zone, zprint calculates how much space is allocated but not currently in use, the space wasted by the zone.
-s zprint sorts the zones, showing the wasting the most memory first.
-c (Default) zprint prints zone info in columns. Long zone names are truncated with '$', and spaces are replaced with '.', to allow
for sorting by column. Pageable and collectible zones are shown with 'P' and 'C' on the far right. Zones with preposterously large
maximum sizes are shown with '----' in the max size and max num elts fields.
-h (Default) Shows headings for the columns printed with the -c option. It may be useful to override this option when sorting by col-
umn.
Any option (including default options) can be overridden by specifying the option in upper-case; for example, -C overrides the (default)
option -c.
SEE ALSO
host_zone_info(2).
27/02/87 ZPRINT(1)