Sponsored Content
Full Discussion: Hp ilo from Linux
Top Forums Shell Programming and Scripting Hp ilo from Linux Post 302849397 by learnbash on Sunday 1st of September 2013 07:04:17 AM
Old 09-01-2013
Hp ilo from Linux

Hi,

I want to do momentary press to one server from linux is it possible? I got this command from internet is it correct? or need changes? I also need help how to start and reboot server in hp ilo from linux server.

Code:
fence_ilo -a 10.1.41.155 -l Admin -p Password

 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Xhost and ILO

I have an application that requires me to disable the restricted access to the X Server libraries by issuing the 'Xhost +' command from a Console Window. It is important that this command is run from the Console Window and not a Terminal Window otherwise the system complains that DISPLAY is not... (0 Replies)
Discussion started by: jimthompson
0 Replies

2. Solaris

HP iLO virtual serial port

Greetings All, If someone/anyone reading this post has had success setting up and configuring HP iLO2 CLI virtual serial port for Solaris...please tell how. I'm trying to get a remote console to an HP DL385 server via iLO2 and ssh. The server is running Solaris 10 (11/06), patched to... (1 Reply)
Discussion started by: alias.256
1 Replies

3. HP-UX

iLo RBSU

Hi, I wanted to setup a ilo for an HP 9000 rp 8420 server. Can anyone have an idea on it? (1 Reply)
Discussion started by: gunnervarma
1 Replies

4. Linux

Findout iLO type installed in a machine

I have to write Linux script to findout what kind of ilo is been installed in the given ip address either ilo/LO100 or no device found. IP address will be given in the command line of the script. -> With out log on to the ip address, should get the ilo type installed in that machine. 1. I... (1 Reply)
Discussion started by: skmdu
1 Replies

5. HP-UX

iLO configuration

how to set IP for iLO in HP server first time thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies

6. Solaris

T5220 ILO not saving static IP

I have a brand new T5220 and I'm trying to configure the ILOM port with a static Ip address via the Serial Management port. I log on as "root" and then enter the commands ( see below) to config the port. When I enter the last command which is " set /SP/network commitpending=true", which I... (9 Replies)
Discussion started by: danfall4
9 Replies

7. Hardware

Reset ILO password

HI Guys I have forgot my ILO password for REDHAT Linux, Its Protriat HP server. I need to set new password for ILO without installing any RPM like "hponfig".... I need to set password in terminal. please give me steps to change the password waiting for ur replys (1 Reply)
Discussion started by: suresh_krish
1 Replies

8. IP Networking

HP iLO using DHCP & Default Password

Hi, I have two questions about HP system iLO: (1) The <HP iLO 2 User Guide> says "Configure the IP address: This step is necessary only if you are using a static IP address. When using dynamic IP addressing, your DHCP server will automatically assign an IP address for iLO 2. HP recommends using... (6 Replies)
Discussion started by: aixlover
6 Replies

9. UNIX for Dummies Questions & Answers

HP DL380 G6 ILO question Linux

Hi, I have Redhat Linux 5.9. I need to connect all the ILO to different switch which can support 1 Gig. How can I find if ILO port can support gigabit? I am on HP website but not able to find anything about this information. Not sure I am looking in the correct place. Please help. (3 Replies)
Discussion started by: samnyc
3 Replies

10. HP-UX

Hp rx2620: is possible to access ILO via serial COM1?

Fast question: a bad reset put ilo ip to 127.0.0.1(!) and now i cannot reach via network Is possible to get ilo via serial using COM1/console? I see three console ports on server back side two are standard and one is reachable only with this cable... 403 Forbidden but i don't have this... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
asadmin-shutdown(1AS)						   User Commands					     asadmin-shutdown(1AS)

NAME
asadmin-shutdown, shutdown - brings down the administration server SYNOPSIS
shutdown [--user admin_user][--password admin_password][--host localhost] [--port 4848][--passwordfile filename][--secure|-s] shutdown gracefully brings down the administration server and all the running instances. You must manually start the administration server to bring it up again. OPTIONS
--user administrative user associated for the instance. --password administrative password corresponding to the administrative user. --host host name of the machine hosting the administrative instance. --port administrative port number associated with the administrative host. --passwordfile file containing passwords appropriate for the command (e.g., administrative instance). --secure if true, uses SSL/TLS to communicate with the administrative instance. Example 1: Using the shutdown command asadmin> shutdown --user admin --password adminadmin --host bluestar --port 4848 Waiting for admin server to shutdown... Admin server has been shutdown EXIT STATUS
0 command executed successfully 1 error in executing the command INTERFACE EQUIVALENT
Administration Server page asadmin-start-instance(1AS), asadmin-stop-instance(1AS), asadmin-restart-instance(1AS)asadmin-start-domain(1AS), asadmin-stop-domain(1AS), asadmin-start-appserv(1AS), asadmin-stop-appserv(1AS) J2EE 1.4 SDK March 2004 asadmin-shutdown(1AS)
All times are GMT -4. The time now is 12:37 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy