04-01-2013
Totally got it to work.
I think the key takeaway of this thread is I successfully converted the raw to vmdk and made vmware think its an ide drive. One tool example is raw2vmdk. I have not found anything to write dd to a real ide drive. Any thoughts? Must the drive be same size same model as the image?
Thanks for all ur response I can see the files in the crashed HDD.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. Solaris
Hi Friends,
I am using VMware 6.0 and i want to transfer some files from External HDD so how to mount the Disk, and i am not able to assign any ip to my network card any one can help me how to set ip in VMware.
Thanks and Regards,
Venky.:b: (0 Replies)
Discussion started by: 1409.venkatesh
0 Replies
5. Windows & DOS: Issues & Discussions
Hi,
Unix based,
My harddrive won't boot and I'm looking for a reliable tool
that can mount a hdd on Windows XP and show me the files
stored on a NFS system.
I tried the tool: Ext2IFS but this didn't work.
I found a lot of tools on google to mount nfs share thru a network
but that's... (1 Reply)
Discussion started by: severt
1 Replies
6. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
7. Filesystems, Disks and Memory
I started on another thread and full story can be seen here: https://www.unix.com/security/91428-how-reset-root-password-old-unix-system-v.html
But my situation turned to land on this thread now.
I have old scsi HDD out of the UHC UNIX System V Rel. 4.0 Version 3.6 box. And need to read... (1 Reply)
Discussion started by: 82026
1 Replies
8. Solaris
Hi,
I need to create 4 zones.
I have an array with a RAID5 volume. I have exported 4 LUNS from the array. Now my host see the 4 LUNS as raw devices.
I am partitioning each LUN using format then mounting each slice on the global zone. Then I am using each slice as a file system for my non... (3 Replies)
Discussion started by: general_lee
3 Replies
9. Solaris
I just installed Solaris 11.2 - and it is a bugger. How do I mount an extra HDD that is now formated to NTFS through gparted
it keeps telling me I don't have any ntfs on this laptop. it has two hdds, /dev/sda1 /dev/sdb1 (Linux lingo) Solaris is installed on primary hard drive back of it. then... (2 Replies)
Discussion started by: userx-bw
2 Replies
10. Emergency UNIX and Linux Support
rying it this way, because I can't handle the slices for the second hdd. If there is someone on this forum who can help me out of that misery, he would really save my digital life in this digital ocean.
So not giving up, reading several times the manual of gpart. But the best hint in all that... (0 Replies)
Discussion started by: 1in10
0 Replies
HT(4) Kernel Interfaces Manual HT(4)
NAME
ht - TM-03/TE-16,TU-45,TU-77 MASSBUS magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NHT ht_drives # TE16, TU45, TU77
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ht ? 172440 224 5 htintr # tu 16 massbus tape
major device number(s):
raw: 6
block: 0
minor device encoding:
bits 0003 specify HT drive
bit 0004 specifies no-rewind operation
bit 0010 specifies 1600BPI recording density instead of 800BPI
DESCRIPTION
The tm-03/transport combination provides a standard tape drive interface as described in mtio(4). All drives provide both 800 and 1600
bpi; the TE-16 runs at 45 ips, the TU-45 at 75 ips, while the TU-77 runs at 125 ips and autoloads tapes.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO
mt(1), tar(1), tp(1), mtio(4), tm(4), ts(4), dtab(5), autoconfig(8)
DIAGNOSTICS
tu%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
tu%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
tu%d: can't change density in mid-tape. An attempt was made to write on a tape at a different density than is already recorded on the
tape. This message is written on the terminal of the user who tried to switch the density.
tu%d: hard error bn%d er=%b ds=%b. A tape error occurred at block bn; the ht error register and drive status register are printed in
octal with the bits symbolically decoded. Any error is fatal on non-raw tape; when possible the driver will have retried the operation
which failed several times before reporting the error.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The system should remember which controlling terminal has the tape drive open and write error messages to that terminal rather than on the
console.
3rd Berkeley Distribution January 28, 1988 HT(4)