Hi,
While I am trying SFTP my machine to another unix machine ,
it was working fine till 10 min back.
But now i am getting the below error
"Request for subsystem 'sftp' failed on channel 0"
Could you please someone help me to solve or analyise the root cause...
Cheers:b:,
Mahiban (0 Replies)
Hi,
i got the following error when i tried to access the cygwin x server from a windows XP PC.
"xdmcp fatal error session failed session 23 failed for display"
Alternatively, when i tried to access the same Cygwin X Server from another windows XP PC which is on a different LAN... (3 Replies)
In AIX 5.1, a daily run script that backing up oracle data failed yesterday with following errors:
The Tivoli backup of DBPROD failed.
What could be the issue, OS, backup or Oracle? (3 Replies)
HI,
I have two Linux servers on which IBM Sterling ConnectDirect is installed. I want to transfer a file from server(abc20) to abc19.
I have edited userfile.cfg & netmap.cfg on both the server still file transfer is not happening. Also the file is getting transferred from abc20 to abc20 itself... (5 Replies)
Hi exports,
I have a T4 with 4 port internal NIC which 2 ports are active and, external one with 4 ports as well with only 2 ports active. So the total of the ports are 4 out of 8. I have created an link aggregation called gnic0 with ports net0, net1, net6 and, net7 in it. I also created a... (0 Replies)
I am again rephrasing the issue that we are facing:
We are creating link aggregations with two interfaces named net0 & net5:
# dladm create-aggr -m dlmp -l net0 -l net5 -l net2 aggr1
Setting prob targets for aggr1:
# dladm set-linkprop -p probe-ip=+ aggr1
Setting failure detection... (3 Replies)
I have created one file that contains all the necessary info in it to create a download link. In each of the lines /results/analysis/output/Home/Auto_user_S5-00580-6-Medexome_67_032/plugin_out/FileExporter_out.67... (8 Replies)
Hi,
I am trying to create aggregation by using dladm, But am getting the following error.
dladm create-aggr -P L2 -l net2 sumaggr2
dladm: create operation failed: link busy
I have checked in dladm show-link and the state is "down"..
dladm show-link | grep ^net2
net2 phys ... (1 Reply)
Hi! I have a Solaris 11 local zone, everything is running fine, BUT, when I issue an "ipadm show-addr" from inside the local zone I get the following:
root@xxxxxxx:/var/opt# ipadm show-addr
ADDROBJ TYPE STATE ADDR
lo0/? inherited ok 127.0.0.1/8... (2 Replies)
Discussion started by: rtmg
2 Replies
LEARN ABOUT BSD
il
IL(4) Kernel Interfaces Manual IL(4)NAME
il - Interlan NI1010 10 Mb/s Ethernet interface
SYNOPSIS
/sys/conf/SYSTEM:
NIL il_controllers # Interlan Ethernet
DESCRIPTION
The il interface provides access to a 10 Mb/s Ethernet network through an Interlan 1010 or 1010A controller.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl. The il interface employs the address resolution
protocol described in arp(4P) to dynamically map between Internet and Ethernet addresses on the local network.
The interface normally tries to use a ``trailer'' encapsulation to minimize copying data on input and output. The use of trailers is nego-
tiated with ARP. This negotiation may be disabled, on a per-interface basis, by setting the IFF_NOTRAILERS flag with an SIOCSIFFLAGS
ioctl.
DIAGNOSTICS
il%d: input error. The hardware indicated an error in reading a packet off the cable or an illegally sized packet.
il%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
il%d: setaddr didn't work. The interface was unable to reprogram its physical ethernet address. This may happen with very early models of
the interface. This facility is used only when the controller is not the first network interface configured for XNS. The oldest interface
tested (2.7.1.0.1.45) has never failed in this way.
The following messages indicate a probable hardware error performing the indicated operation during autoconfiguration or initialization.
The status field in the control and status register (the low-order four bits) should indicate the nature of the failure. See the hardware
manual for details.
il%d: reset failed, csr=%b.
il%d: status failed, csr=%b.
il%d: hardware diag failed, csr=%b.
il%d: verifying setaddr, csr=%b.
il%d: stray xmit interrupt, csr=%b.
il%d: can't initialize.
SEE ALSO intro(4N), inet(4F), arp(4P)3rd Berkeley Distribution August 20, 1987 IL(4)