When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software.
I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server... (1 Reply)
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies
LEARN ABOUT REDHAT
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO mknod(1), chown(1), mount(8), sd(4)Linux 1992-12-17 HD(4)