11-15-2012
It would probably be easier to install SCO on another system, and add the disk as a second drive.
If you do this, use extreme caution when running 'mkdev hd' and 'divvy'.
'divvvy' will show you the existing partitions, but not their names, as these are stored on the boot drive. Enter the names of the partitions, and make sure that none of the partitions is marked as 'new'.
You will then be able to mount the partitions to any directory.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
# grep "Jul 3" syslog.messages | more
Jul 3 00:16:03 www3 CPU3: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:16:08 www3 CPU3: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:17:01 www3 CPU2: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:17:06 www3 syslogd: /usr/adm/debug: No space... (1 Reply)
Discussion started by: Cameron
1 Replies
2. UNIX for Dummies Questions & Answers
Hello all. I am receiving this message on the console of a SCO Openserver 5.0.7 server. The hardware is IBM, running mirrored SCSI drives with a hot-swap spare off of an IBM Serveraid controller. I suspect that some permutation of fsck can help me resolve whatever is causing the error, but I am... (0 Replies)
Discussion started by: DoublePanic
0 Replies
3. UNIX for Advanced & Expert Users
If somebody solve this error please help me!
Thanks in advance! :confused: (7 Replies)
Discussion started by: FCollet
7 Replies
4. SCO
I have a 17GB SCSI disk in an SCO 5.0.6 server and it's running out of space because of a growing database on the disk. Consequently I would like to upgrade the 17GB to a 74GB disk and extend the partition.
First off, is partition extension available under HTFS - I know this is an old... (1 Reply)
Discussion started by: carribey
1 Replies
5. UNIX for Dummies Questions & Answers
i am about to install oracle on my solaris x86-64
This installation require 4Gb space and i qish to do this installation on the directory
/u01/app/oracle
The following was my approch
mkdir -p /u01/app/oracle
i then use the command below to see if there is enough space
# df -h... (6 Replies)
Discussion started by: seyiisq
6 Replies
6. Solaris
Hi all,
currently , my root filesystem already reach 90 ++%
I already add more cylinder in the root partition as below
Part Tag Flag Cylinders Size Blocks
0 root wm 67 - 5086 38.46GB (5020/0/0) 80646300
1 swap wu 1 - ... (11 Replies)
Discussion started by: SmartAntz
11 Replies
7. UNIX for Dummies Questions & Answers
Hi,
How to mount HTFS FS (from SCO UNIX) under linux?
Best regards.
where is link: htfs_fs-0.01alpha.tar.bz2 (2 Replies)
Discussion started by: EMREZ
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I wanted to find out that in my database server which filesystems are shared storage and which filesystems are local. Like when I use df -k, it shows "filesystem" and "mounted on" but I want to know which one is shared and which one is local.
Please tell me the commands which I can run... (2 Replies)
Discussion started by: kamranjalal
2 Replies
9. Solaris
Hi guys!
Could you tell me what's the difference of filesystem of Solaris to filesystem of Windows? I need to compare both.
I have read some over the net but it's so much technical. Could you explain it in a more simpler term? I am new to Solaris. Hope you help me guys.
Thanks! (4 Replies)
Discussion started by: arah
4 Replies
10. AIX
Dear all,
We are facing prolem when we are going to mount AIX filesystem, the system returned the following error
0506-307The AFopen call failed
: A file or directory in the path name does not exist.
But when we ls filesystems in the /etc/ directory it show
-rw-r--r-- 0 root ... (2 Replies)
Discussion started by: m_raheelahmed
2 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)