Sponsored Content
Operating Systems Linux Red Hat ifconfig eth0 unplumb equivalent Post 302723221 by DukeNuke2 on Monday 29th of October 2012 04:56:27 PM
 

10 More Discussions You Might Find Interesting

1. IP Networking

Adding an IP to eth0

Hi there guys! I have a small task that I have to accomplish, but I don't seem to be able to do that. I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies

2. UNIX for Dummies Questions & Answers

ifconfig eth0 and awk and grep

if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host (1 Reply)
Discussion started by: carlvernon
1 Replies

3. IP Networking

what is "unplumb"

I saw an example on the web, it is an HP-UX command: ifconfig lan0 unplumb ifconfig lan0 plumb so what is plumb actually, I check HP-UX man page and still no idea. What is the difference if I do in this way? ifconfig lan0 down ifconfig lan0 up :confused: (1 Reply)
Discussion started by: tommy_cs
1 Replies

4. Red Hat

ifcfg-eth0 and eth1 is N/A

when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in /etc/sysconfig/network-scripts/. what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies

5. UNIX for Dummies Questions & Answers

how can I find which one is eth0?

Hi, Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0? Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies

6. Red Hat

Device eth0 issue

Hi, I have just installed RHEL 5.4 on a BL430c-class server and I am attempting to connect to the network only when I try and start eth0, I get the following error? "Bringing up Interface eth0: hp device eth0 does not seem to be present, delaying initialization." I am using a HP... (18 Replies)
Discussion started by: Duffs22
18 Replies

7. Red Hat

VMBox not Recognizing eth0 on RH.

Hello, I re-installed my laptop and installed a new copy of VMBOX, I created a VM Machine with my Rhel5 and a CEntos copy as well. I am using a laptop HP DV4, I use wireless on the laptop. Usually when I boot up in to either machine I would get eht0 and lo as usual now I just don't get... (4 Replies)
Discussion started by: NelsonC
4 Replies

8. Red Hat

Eth0 Limitations

Hi, I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine. I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows: Settings for eth0: Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies

9. IP Networking

iptables On for eth0 and off for other interfaces

Hi all, I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic. I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies

10. Red Hat

Eth0 not running in redhat 6.4

Hi guys, I really need your help with this. My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same. It just would not come up. Please please I will really appreciate the help here. Thank you in advance. (3 Replies)
Discussion started by: cjashu
3 Replies
purple-url-handler(1)						   User Commands					     purple-url-handler(1)

NAME
purple-url-handler - Python script to handle URL with purple SYNOPSIS
purple-url-handler [-URL] DESCRIPTION
Python script to handle URL with purple. OPTIONS
Usage: purple-url-handler URL Example: purple-url-handler "xmpp:romeo@montague.net?message" ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWgnome-im-client | +-----------------------------+-----------------------------+ |Interface stability |Volatile | +-----------------------------+-----------------------------+ SEE ALSO
purple-remote(1), purple-send(1), purple-send-async(1), attributes(5) purple-url-handler Manual, http://pidgin.im/ NOTES
Updated by Lei Ju, Sun Microsystems Inc., 2006, 2007. SunOS 5.11 02 Apr 2008 purple-url-handler(1)
All times are GMT -4. The time now is 05:16 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy