ifconfig eth0 unplumb equivalent Post: 302723221

10 More Discussions You Might Find Interesting

1. IP Networking

Adding an IP to eth0

Hi there guys! I have a small task that I have to accomplish, but I don't seem to be able to do that. I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to...

2. UNIX for Dummies Questions & Answers

ifconfig eth0 and awk and grep

if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host

3. IP Networking

what is "unplumb"

I saw an example on the web, it is an HP-UX command: ifconfig lan0 unplumb ifconfig lan0 plumb so what is plumb actually, I check HP-UX man page and still no idea. What is the difference if I do in this way? ifconfig lan0 down ifconfig lan0 up :confused:

4. Red Hat

ifcfg-eth0 and eth1 is N/A

when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in /etc/sysconfig/network-scripts/. what will i do?

5. UNIX for Dummies Questions & Answers

how can I find which one is eth0?

Hi, Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0? Please advice.

6. Red Hat

Device eth0 issue

Hi, I have just installed RHEL 5.4 on a BL430c-class server and I am attempting to connect to the network only when I try and start eth0, I get the following error? "Bringing up Interface eth0: hp device eth0 does not seem to be present, delaying initialization." I am using a HP...

7. Red Hat

VMBox not Recognizing eth0 on RH.

Hello, I re-installed my laptop and installed a new copy of VMBOX, I created a VM Machine with my Rhel5 and a CEntos copy as well. I am using a laptop HP DV4, I use wireless on the laptop. Usually when I boot up in to either machine I would get eht0 and lo as usual now I just don't get...

8. Red Hat

Eth0 Limitations

Hi, I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine. I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows: Settings for eth0: Supported ports: ...

9. IP Networking

iptables On for eth0 and off for other interfaces

Hi all, I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic. I need to achieve this by editing...

10. Red Hat

Eth0 not running in redhat 6.4

Hi guys, I really need your help with this. My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same. It just would not come up. Please please I will really appreciate the help here. Thank you in advance.

LEARN ABOUT SUSE

ifcfg-vlan

IFCFG-VLAN(5)						       Network configuration						     IFCFG-VLAN(5)

NAME

       ifcfg-vlan - virtual LAN interface configuration

SYNOPSIS

       /etc/sysconfig/network/ifcfg-vlan*

Virtual LANs (802.1q)
       To setup a vlan interface you need a configuration file that contains at least the mandatory

       ETHERDEVICE
	      variable with the real interface used for the virtual LAN.

       Further, it may contain the optional

       VLAN_ID
	      variable that specifies the VLAN ID.

       By default and when the VLAN_ID variable is not set, the number at the end of the interface name is the VLAN ID.

       Preferably the interface name and the configuration file follow the VLAN interface name scheme (type), that is either:
	      ifcfg-vlan<VLAN-ID> (e.g. ifcfg-vlan42)

	      or

	      ifcfg-name.<VLAN-ID> (e.g. ifcfg-eth0.42)

       The VLAN-ID can be also 0-padded (e.g. ifcfg-vlan0042 or ifcfg-eth0.0042).

       Also  in case of custom names, trailing digits are interpreted as VLAN-ID by default (e.g. ifcfg-dmz42). When VLAN_ID is set in the config,
       the interface name have any name (e.g. ifcfg-foobar).

       Note: The drawback of custom interface names and VLAN_ID usage is, that a rename of the interface is required and  that	they  violate  the
       name scheme.

       The  real  interface will be set UP automatically and doesn't need a config file in case of a physical interface. But without a config file
       YaST will consider this interface as unused, if will not follow hotplug	events	and  you're  unable  to  apply	any  settings,	e.g.  ETH-
       TOOL_OPTIONS. To avoid that, provide an config file with at least STARTMODE='auto'.

       The  rest  of  the VLAN interface IP and routes configuration do not differ from ordinary interfaces. See also man ifcfg and man routes for
       details.

EXAMPLES

       Sets up vlan3 vlan interface on top of eth0:

	      ifcfg-vlan3
		 STARTMODE='auto'
		 ETHERDEVICE='eth0'
		 IPADDR='192.168.3.27/24'

       Sets up eth0.3 vlan interface on top of eth0:

	      ifcfg-eth0.3
		 STARTMODE='auto'
		 ETHERDEVICE='eth0'
		 IPADDR='192.168.3.27/24'

       Sets up lan1 vlan interface with ID 42 on top of eth0:

	      ifcfg-lan1
		 STARTMODE='auto'
		 ETHERDEVICE='eth0'
		 VLAN_ID='42'
		 IPADDR='192.168.3.27/24'

BUGS

       Please report bugs at <http://www.suse.de/feedback>

AUTHOR

       Christian Zoz <zoz@suse.de>
       Michal Svec <msvec@suse.cz>
       Bjoern Jacke
       Mads Martin Joergensen <mmj@suse.de>
       Michal Ludvig <mludvig@suse.cz>
       Marius Tomaschewski <mt@suse.de>

SEE ALSO

       routes(5), ifcfg(5), ifup(8).

sysconfig							    August 2004 						     IFCFG-VLAN(5)