Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Folks;
I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it.
Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card?
I... (1 Reply)
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT HPUX
vtdaemon
vtdaemon(1M)vtdaemon(1M)NAME
vtdaemon - respond to vt requests
SYNOPSIS
lan_device lan_device ...
DESCRIPTION
responds to requests from other systems (via local area network) made by (see vt(1)). spawns a server to respond to each request that it
receives.
Options
recognizes the following command-line options and arguments:
Causes to rebroadcast all requests received on one lan device to all other lan devices specified on the command line. The
optional parameter ngateway specifies the maximum number of vtgateway servers that can be in operation concurrently. If
ngateway is not specified, there is no limit on the number of vtgateway servers that can be in operation concurrently.
Causes vtdaemon to ignore all requests that have come through a gateway.
The remaining arguments are the full path names of lan devices that vtdaemon looks for requests on. If no lan devices are specified, the
default lan device is used.
The major number for this device must correspond to a IEEE 802.3 local area network device.
Another function of is to create portals and service portal requests. A portal is a callout device that can be used by to communicate to
another machine via local area network (see uucico(1M)). Portals are created by according to the configuration information found in the
file Each line in has the format:
<calldev>[,<lan device>] <nodename>
For each line, creates a portal named calldev in Whenever this device is opened, spawns a server that creates a connection to the system
specified by nodename via the lan device specified. If no lan device is specified, the first one specified on the command line when was
started is used (or the default lan device is used if no lan devices were specified on the command line).
should be terminated by sending signal to it. When receives this signal it removes all of the portals it created in before exiting.
DIAGNOSTICS
Diagnostics messages produced by are written to
WARNINGS
uses the Hewlett-Packard (Link Level Access) direct interface to the HP network drivers. uses the multicast address It should not be used
or deleted by other applications accessing the network. uses the following IEEE 802.3 sap (service access point) values: and They should
not be used by other applications accessing the network.
Desktop HP-UX
If your system has been installed with the Desktop HP-UX product, then both and will not be started by default. In order to start these
daemons, change PTYDAEMON_START and VTDAEMON_START from a "0" to a "1" in the and files, respectively. The system must either be rebooted
for these changes to take effect, or you can manually start both daemons by typing :
where /dev/lan0 is the character special device file corresponding to the IEEE802.3 local area network device.
FILES
logfile used by vtdaemon.
default lan device name.
SEE ALSO vt(1), uucico(1M).
vtdaemon(1M)