10-10-2012
during bootup of the ALOM (powercycle!) press the ESC key. this should bring you to a menu where you can reset the password.
9 More Discussions You Might Find Interesting
1. Solaris
I have one Sun Netra T2000 Server. The ALOM SC admin password of this server is not known. Could you anyone help and tell me how can i reset the SC admin account password??
Thanks in advance.. (2 Replies)
Discussion started by: sudhir_shet
2 Replies
2. Solaris
Hi Guyz,
I recently downloaded sol-10-u6-ga1-sparc-dvd.iso from Sun. I burned the disk as cd .iso.
When trying to boot at the ok> boot cdrom
i get the following error:
-----------------------------------------------------------------------
Boot device:... (2 Replies)
Discussion started by: Mwamba
2 Replies
3. Solaris
Hi, i am really 'fresh' to Solaris or any UNIX OS. My role as web developer but i need slightly involve to Solaris support. It is harder for me to understand it and i recently encounter a problems.
/var file system (/dev/md/rdsk/d425) is being checked.
run fsck -F ufs /dev/md/rdsk/d425
... (8 Replies)
Discussion started by: webster5u
8 Replies
4. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
5. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
6. Solaris
Hi:
I bougth an used Sun Fire v440, and It have a firmware password. When I turn on the server, it ask for firmware password. (I don 't know what is the correct password). I can access to SC, but when I want to access to OBP, Firmware Password appears again. I remove the battery for two hours,... (1 Reply)
Discussion started by: mguazzardo
1 Replies
7. Hardware
Hello,
I am trying to perform Suse 10 SP3 installation via network in 6 Sun Fire 4270 M2 servers.
The problem is that even if i set first prio boot device the hard disk the system always try to boot from network.And after the first restart the BIOS setting has been lost(and PXE come first... (2 Replies)
Discussion started by: @dagio
2 Replies
8. Solaris
I am administering a Solaris 10 server that I have root password for but need to get to the system server console. The password has been 'forgotten'.
I've tried changing it in /var/opt/mps/serverroot/admin-serv/config/admpw and local.conf with the current hashed password in /etc/shadow for a... (4 Replies)
Discussion started by: jameson
4 Replies
9. Solaris
Dear all
Can you help me to reset RSC from Sun V490
Inside this machine the Operating System is broken..
please help guys
thanks (1 Reply)
Discussion started by: gema.utama
1 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)
NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS
--predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO
bup-midx(1), bup-save(1)
BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown- bup-margin(1)