Sponsored Content
Operating Systems Linux Red Hat configuring broadcast traffic to heart commuication RH cluster Post 302690243 by bobby320 on Wednesday 22nd of August 2012 04:43:09 PM
Old 08-22-2012
I was going to knowledge base for your post, and I am planning to use gfs2 filesystem for clustering mysql database. after going through this documentation broadcast mode is not suitable mode for GFS2 ? so what will be alternate mode to configuring filesystem.
Code:
Broadcast mode is not suitable for deployments that require high performance locking. Examples include the following:
GFS/GFS2 deployments that use file locking extensively.
Cmirror usage
Any use of Corosync/OpenAIS outside of Red Hat Enterprise Linux that would require high performance message transport, such as Apache Qpid messaging.

Thanks
 

6 More Discussions You Might Find Interesting

1. AIX

Configuring new disks on AIX cluster

We run two p5 nodes running AIX 5L in a cluster mode (HACMP), both the nodes share external disk arrays. Only the primary node can access the shared disks at a given point of time. We are in the process of adding two new disks to the disk arrays so as to make them available to the existing... (3 Replies)
Discussion started by: dnicky
3 Replies

2. AIX

POWER HA 5.5 & Service IP / disk heart beat

Hello, I have a quick question regarding POWER HA ( HACMP ) 5.5 ; I have four ethernet adapters en0 en1 en2 en3 en0 is configured as BOOT_IP with IP address all other ethernet adapters are empty en1 / en2 / en3 so when I configure the service IP and start HACMP , the service IP... (2 Replies)
Discussion started by: filosophizer
2 Replies

3. AIX

Should GPFS be configured before/after configuring HACMP for 2 node Cluster?

Hi, I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS. I have two LPARs on which GPFS is configured (4-5 disks) Now these two LPARs need to be configured for HACMP (PowerHA) as well. What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies

4. What is on Your Mind?

Heart beat monitor using android

I just had this idea of using Android (a linux derivative) to monitor heart rates of patients with a history of cardiac problems. There are plenty apps around that monitor heart rates, but none for people that require medical attention when their heart rate drops below a certain level for more... (0 Replies)
Discussion started by: figaro
0 Replies

5. UNIX for Dummies Questions & Answers

Heart OS and Love OS?

Hi everyone. Our professor in Operating Systems gave us a research work about the Heart OS and Love OS. We were told that they were old operating systems from UNIX but I couldn't find any information about them from google. I hope someone here could point me to the right direction. Thanks! (7 Replies)
Discussion started by: jogonjr
7 Replies

6. Red Hat

configuring MYsql db on redhat cluster

Hello, can someone please suggest me in configuring the mysql db on redhat cluster, I have few questions. 1. where do I have to configure heart beat links, and is there any file in the redhat cluster that we update it to use these ipaddress and these interface on the node. 2. I am configuring... (0 Replies)
Discussion started by: bobby320
0 Replies
CLUSTER(1)						      General Commands Manual							CLUSTER(1)

NAME
cluster - find clusters in a graph and augment the graph with this information. SYNOPSIS
cluster [-v?] [ -Ck ] [ -ck ] [ -o outfile ] [ files ] DESCRIPTION
cluster takes as input a graph in DOT format, finds node clusters and augments the graph with this information. The clusters are specified by the "cluster" attribute attached to nodes; cluster values are non-negative integers. cluster attempts to maximize the modularity of the clustering. If the edge attribute "weight" is defined, this will be used in computing the clustering. OPTIONS
The following options are supported: -Ck specifies a targeted number of clusters that should be generated. The specified number k is only a suggestion and may not be real- isable. If k == 0, the default, the number of clusters that approximately optimizes the modularity is returned. -ck specifies clustering method. If k == 0, the default, the modularity will be used. If k == 1 modularity quality will be used. -ooutfile Specifies that output should go into the file outfile. By default, stdout is used. -v Verbose mode. EXAMPLES
Applying cluster to the following graph, graph { 1--2 [weight=10.] 2--3 [weight=1] 3--4 [weight=10.] 4--5 [weight=10] 5--6 [weight=10] 3--6 [weight=0.1] 4--6 [weight=10.] } gives graph { node [cluster="-1"]; 1 [cluster=1]; 2 [cluster=1]; 3 [cluster=2]; 4 [cluster=2]; 5 [cluster=2]; 6 [cluster=2]; 1 -- 2 [weight="10."]; 2 -- 3 [weight=1]; 3 -- 4 [weight="10."]; 4 -- 5 [weight=10]; 5 -- 6 [weight=10]; 3 -- 6 [weight="0.1"]; 4 -- 6 [weight="10."]; } AUTHOR
Yifan Hu <yifanhu@research.att.com> SEE ALSO
gvmap(1) Blondel, V.D., Guillaume, J.L., Lambiotte, R., Lefebvre, E.: Fast unfolding of communities in large networks. Journal of Statistical Mechanics: Theory and Experiment (2008), P10008. 3 March 2011 CLUSTER(1)
All times are GMT -4. The time now is 04:03 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy