I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
as for the arp_ip_target I set it to the gateway address as m not using a router. Is this correct? or I shall set the other two system IPs there?
Next, I edited the interfaces file, /etc/network/interfaces:
and finally loading bonding module into the kernel and ifconfig.
if anyone has done this before, I would highly appreciate if you could tell me the exact procedure.
I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Hello.
Our Company is spreaded over Germany.
There are main offices an branch offices.
These offices are mostly connecte via multiple sdsl.
We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances.
It seemed that only one VPN Connetion between to offices could be... (0 Replies)
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Dear All ,
Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x.
After configuring , we restarted the network services , the link was down after that , we could not login in to the Server.
So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies
LEARN ABOUT CENTOS
bond2team
BOND2TEAM(1) Bonding to Team conversion tool BOND2TEAM(1)NAME
bond2team -- Converts bonding configuration to team
SYNOPSIS
bond2team [options]
DESCRIPTION
bond2team is a tool to convert bonding options to team trying as much as possible to keep the original functionality.
The resulting files are saved in a temporary directory using ifcfg style by default. In the case of converting an ifcfg file, it translates
the bonding options to team, preserving all other options. In that case, it converts the respective slave ifcfg files to team port, pre-
serving all their other options too. In case of converting from given bonding options in the command line, the tool can use the specified
ports as team ports.
OPTIONS --master <interface>
Specify the interface name or ifcfg file to convert. If the interface name is specified, the tool will look at
/etc/sysconfig/network-scripts/ for the respective ifcfg file.
--rename <interface>
This is a convenient option to replace the original interface name by the specified name. For instance, if --master specifies bond0,
it is possible to use --rename team0 to change the final interface name to team0.
--ifcfg
Set the output format to ifcfg config style. [default]
--json Set the output format to JSON style. See teamd.conf(5) for further details.
--bonding_opts '<bonding options>'
Specify the bonding options to be converted instead of reading them from the ifcfg file.
--port <interface>
Set the specified interface as a team port.
--configdir <directory>
Change the ifcfg configuration path from /etc/sysconfig/network-scripts to the specified <directory>.
--outputdir <directory>
Set the output directory to <directory>.
--stdout
Print the result to the screen instead of writing to files.
--debug
Increase the debugging level.
--quiet
Disallow any messages to be printed to console.
--version
Print tool version to console and exit.
--help Print help text to console and exit.
--examples
Print common usage examples to console and exit.
EXAMPLES
To convert the current 'bond0' ifcfg configuration to team ifcfg:
# bond2team --master bond0
To convert the current 'bond0' ifcfg configuration to team ifcfg renaming the interface name to 'team0'. Caution : firewall rules, alias
interfaces, etc., that might be tied to the original interface name can break after the renaming because the tool will only change the
ifcfg file, nothing else.
# bond2team --master bond0 --rename team0
To convert given bonding parameters with ports without any ifcfg:
# bond2team --bonding_opts 'mode=1 miimon=500 primary=eth1 primary_reselect=0' --port eth1 --port eth2 --port eth3 --port eth4
For more examples, see the option --examples.
CAVEATS
The tool will not convert any other configuration which might be tied to the current setup. For instance, firewall rules, alias interfaces,
bridges, and so on.
AUTHOR
Flavio Leitner is the original author of the tool. Jiri Pirko is the original author and current maintainer of libteam.
SEE ALSO teamd(8), teamdctl(8), teamd.conf(5), teamnl(8)libteam 2013-07-18 BOND2TEAM(1)