05-24-2012
Thanks for the info jgt. unfortunately the system that is going to rest on the sco calls for 507. however i do have 6.o install disk. problem i have is configuring the hard drive partitions. install instructions i have for 507 (to be compatable) shows different setup screen than 6.0 when i get to the section to setup the drive.
10 More Discussions You Might Find Interesting
1. SCO
I've installed a CD-RW rom using SCO OSR 5.0.7, but I cannot open the dev to perform backup (6 Replies)
Discussion started by: tsc_hk
6 Replies
2. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
3. Solaris
Hi,
I attached the CDROM device in sun 2500 system , Now i want to mount this device.
From where i can find the CDROM device.
Thnx.. (2 Replies)
Discussion started by: Aamir Sahil
2 Replies
4. SCO
Looking for specifically naming convention for a tape device for SCO Unix
What full system backup command should I use for SCO UNIX (1 Reply)
Discussion started by: jedimaster
1 Replies
5. Solaris
Hi,
I've seen similar posts on this board about ejecting CDROMs but I've tried the solutions people suggested but still cannot eject the CD. It's stuck in a production box so I can't reboot it...
bash-3.00# eject -f cdrom
/vol/dev/dsk/c0t0d0/sol_10_106_sparc/s0: Device busy
bash-3.00#... (14 Replies)
Discussion started by: jimmy54321
14 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. SCO
This is my first load of SCO OpenServer v5.0.7 on a HP ProLiant ML350 G6. When it asks me to identify the source media it can't find it no matter how I respond. The SCO compatible page says it used the on board SATA DVD-ROM on Port 2 of the embedded SATA controller with "Legacy IDE emulation (as... (8 Replies)
Discussion started by: farmboy
8 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. HP-UX
Hello,
I am following the HPUX 11.31 install/update guide and I am trying to install "Update-UX" from the installation media. I put the CD into the drive, and I am trying to mount the device. The instructions state:Find the DVD-ROM device file name:
ioscan -C disk -f -n -k | more
A typical... (5 Replies)
Discussion started by: bstring
5 Replies
10. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)