05-21-2012
when you boot your server ... it taking minimum 15 mins for bringup ... plz wait ..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
We have a SunFire V880, hooked up with 2 T3 arrays. When ever we issue a reboot command on the system, it hangs at the same place right where it says
syncing file systems done.
To bring it back we shutdown power and it comes clean.
By the way init 6 command works fine.
Has anyone come... (3 Replies)
Discussion started by: smohd
3 Replies
2. AIX
I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software.
I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Discussion started by: craigp84
4 Replies
3. Solaris
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies
4. Shell Programming and Scripting
Hi all,
I have made a script which logins to remote servers and fetches some data from it.
Is is working perfectly when all servers are reachable
BUT
my problem is -- if in case a server is down (or not reachable), the script hangs.
Is there some way, that the script just continues to ssh... (6 Replies)
Discussion started by: vikas027
6 Replies
5. AIX
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies
6. AIX
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies
7. Ubuntu
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies
8. AIX
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Discussion started by: a_sim
15 Replies
9. Solaris
I have a Sun-Fire-V210, the Server hangs for sometime and evn console wont be abled to access and after sometime the server comes back active. the messages file shows this , whats causing this ?
# tail -500 messages
Jan 25 07:02:16 xxxxxxxxxxxxx Corrupt label; wrong magic number
Jan 25... (2 Replies)
Discussion started by: Sojourner
2 Replies
10. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
LEARN ABOUT DEBIAN
muroar_beep
muroar_beep(3) muRoar Programmer's Manual muroar_beep(3)
NAME
muroar_beep - Send notify beep to RoarAudio sound daemon
SYNOPSIS
#include <muroar.h>
int muroar_beep (muroar_t fh);
DESCRIPTION
This function sends a notify beep to the sound daemon fh is connected to. fh need to be connected using muroar_connect(3) to a sound
server supporting the RoarAudio protocol and the BEEP command.
RETURN VALUE
On success this call return 0. On error, -1 is returned.
NOTES
The beep is canceld at the server side as soon as the connection is closed. This means that you should not close the connection before the
beep is played completely.
BUGS
This commands requests the server for a default beep. No other kind of beep can be send. There is in addition no way to tell the actual
length of the beep. The application should at least wait a bit more than 512ms before closing the socket. In case possible it is good to
wait a minimum of about one secound to be really sure the beep ended.
HISTORY
This function first appeared in muRoar version 0.1rc2.
SEE ALSO
muroar_connect(3), muroar_quit(3), RoarAudio(7).
muRoar April 2012 muroar_beep(3)