05-17-2012
Check the apache error log for messages.
Is it working on the command line?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
WITHOUT shutdown X ???
thanks ,
Ivan (6 Replies)
Discussion started by: oneivan
6 Replies
2. BSD
Hello
I installed mysql41 this is the end of the installation
but when I try to launch the mysqld daemon it write this:
note: LodelServoo is a CMS which need mysql
I verify that the dir mysql existed under /var/db, but it doesn't so naively I created it and launch again the mysqld... (4 Replies)
Discussion started by: SoulCoder
4 Replies
3. Shell Programming and Scripting
Hi everybody !
I writed php code so exec bash shell via php (SMS Send via bash shell) but i have problem as follow :
1. When i exec from linux mode : ./sms.sh --- output is "Messages ... OK". Then all message has been sent.
2. When i exec from PHP site --- return value is "Message ... OK" on... (1 Reply)
Discussion started by: lamthenhan
1 Replies
4. Web Development
I need to restart my apache, but apachectl configtest tells me that
Syntax error on line 208 of /etc/httpd/conf/httpd.conf:
Cannot load /usr/local/apache/libexec/libphp4.so into server: /usr/local/apache/libexec/libphp4.so: undefined symbol: ap_signal
I've tried rebuilding php, I'm not... (2 Replies)
Discussion started by: tatebn
2 Replies
5. Shell Programming and Scripting
HI,
Does anybody know if its possible to execute a command through exec,
shell exec, system and if the program doesn't terminate in N seconds
returns control to PHP ?
reg,
research3
---------- Post updated 10-16-09 at 12:20 AM ---------- Previous update was 10-15-09 at 11:03 PM... (1 Reply)
Discussion started by: research3
1 Replies
6. Red Hat
Hi,
I am experiencing frequent system hangs, hard kernel panics, etc almost thrice a day. The system would be totally unresponsive and the only way is to reboot is hard power recycling (plug out the power cable and plug in back after 30 secs). I enabled kdump, but unfortunately the kdump files... (3 Replies)
Discussion started by: massoo
3 Replies
7. UNIX for Dummies Questions & Answers
Hi bros
I have a VPS 512mb (Burst 2GB) with Kloxo installed and hosting few sites on it with not much traffic
I am facing high cpu load for the last few days and seems mysqld is overloading the cpu
Any suggestion will be appreciated
Regards
Rizwan
Top output is as under
top -... (2 Replies)
Discussion started by: rizwan65
2 Replies
8. Red Hat
Hello,
I have recently installed MySql and I encourage an error.
I am using Fedora 15 and when I am trying to start mysqld service i am getting
the following error message:
Starting mysqld (via systemctl): Job failed. See system logs and 'systemctl status' for details. If I try to start it... (4 Replies)
Discussion started by: dot_pro
4 Replies
9. Shell Programming and Scripting
I have the following bash script lines in a file named test.sh.
#!/bin/bash
#
# Write Date to cron.log
#
echo "Begin SSI Load $(date +%d%b%y_%T)"
#
# Get the latest rates file for processing.
#
d=$(ls -tr /rms/data/ssi | grep -v "processed" | tail -n 1)
filename=$d
export filename... (3 Replies)
Discussion started by: ginowms
3 Replies
10. Homework & Coursework Questions
I am trying to start a server for a class I am in but... mysql won't start with this error ( ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) )
---------- Post updated at 03:51 PM ---------- Previous update was at 03:50 PM ----------
... (2 Replies)
Discussion started by: Slayer939
2 Replies
LEARN ABOUT CENTOS
pmdaapache
PMDAAPACHE(1) General Commands Manual PMDAAPACHE(1)
NAME
pmdaapache - Apache2 web server performance metrics domain agent (PMDA)
SYNOPSIS
$PCP_PMDAS_DIR/apache/pmdaapache [-d domain] [-l logfile] [-U username] [-S server] [-P port] [-L location]
DESCRIPTION
pmdaapache is a Performance Metrics Domain Agent (PMDA) which extracts performance metrics describing the state of an Apache web server.
The apache PMDA exports metrics that measure the request rate, cumulative request sizes, uptime and various connection states for active
clients.
This information is obtained by performing a HTTP request to the server status URL, which must be enabled in the httpd.conf configuration
file.
ExtendedStatus on
<Location /server-status>
SetHandler server-status
Order deny,allow
Deny from all
Allow from localhost
</Location>
A brief description of the pmdaapache command line options follows:
-d It is absolutely crucial that the performance metrics domain number specified here is unique and consistent. That is, domain should
be different for every PMDA on the one host, and the same domain number should be used for the same PMDA on all hosts.
-l Location of the log file. By default, a log file named apache.log is written in the current directory of pmcd(1) when pmdaapache is
started, i.e. $PCP_LOG_DIR/pmcd . If the log file cannot be created or is not writable, output is written to the standard error
instead.
-S Query the Apache status information from the named server rather than the local host.
-P Query the Apache status information from the given port rather than the default (80).
-L Specify an alternative location for finding the server-status page.
-U User account under which to run the agent. The default is the unprivileged "pcp" account in current versions of PCP, but in older
versions the superuser account ("root") was used by default.
INSTALLATION
If you want access to the names, help text and values for the apache performance metrics, do the following as root:
# cd $PCP_PMDAS_DIR/apache
# ./Install
If you want to undo the installation, do the following as root:
# cd $PCP_PMDAS_DIR/apache
# ./Remove
pmdaapache is launched by pmcd(1) and should never be executed directly. The Install and Remove scripts notify pmcd(1) when the agent is
installed or removed.
FILES
$PCP_PMCDCONF_PATH
command line options used to launch pmdaapache
$PCP_PMDAS_DIR/apache/help
default help text file for the apache metrics
$PCP_PMDAS_DIR/apache/Install
installation script for the pmdaapache agent
$PCP_PMDAS_DIR/apache/Remove
undo installation script for the pmdaapache agent
$PCP_LOG_DIR/pmcd/apache.log
default log file for error messages and other information from pmdaapache
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
SEE ALSO
PCPIntro(1), httpd(8), pmcd(1), pcp.conf(5) and pcp.env(5).
Performance Co-Pilot PCP PMDAAPACHE(1)