05-08-2012
How did you create it?
Technically none of the Linux kernel settings except compiled-in ones are permanent, they get set by system init scripts and the like on boot.
Last edited by Corona688; 05-08-2012 at 07:24 PM..
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i am running solaris 9 i now how to create virtual ip address but how do i keep them so when the server reboots they are still there?...THANX (2 Replies)
Discussion started by: rmuhammad
2 Replies
2. IP Networking
Hi,
I bound a virtual IP to a network card on my E450 server and I am getting this error when I reboot the server, saying, " retrying host, RPC time out. I had to break this sequence and allow other services to load. Of course they didn't load properly. Please how can I sort this out? I do need... (8 Replies)
Discussion started by: Ronny
8 Replies
3. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
6. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
7. UNIX for Dummies Questions & Answers
All,
I have a question regarding setting up a virtual interface to recieve snmp traps from network devices.
My Solaris 10 server is running the HPOV-NNMi application. The network devices in our environment (many thousands) are all pre-configured to send their snmp traps to a specific IP... (4 Replies)
Discussion started by: turk22
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT LINUX
startpar
STARTPAR(8) System Manager's Manual STARTPAR(8)
NAME
startpar - start runlevel scripts in parallel
SYNOPSIS
startpar [-p par] [-i iorate] [-t timeout] [-T global_timeout] [-a arg] prg1 prg2 ...
startpar [-p par] [-i iorate] [-t timeout] [-T global_timeout] -M [ boot|start|stop]
DESCRIPTION
startpar is used to run multiple run-level scripts in parallel. The degree of parallelism on one CPU can be set with the -p option, the
default is full parallelism. An argument to all of the scripts can be provided with the -a option. Processes block by pending I/O will
weighting by the factor 800. To change this factor the option -i can be used to specify an other value.
The output of each script is buffered and written when the script exits, so output lines of different scripts won't mix. You can modify
this behaviour by setting a timeout.
The timeout set with the -t option is used as buffer timeout. If the output buffer of a script is not empty and the last output was timeout
seconds ago, startpar will flush the buffer.
The -T option timeout works more globally. If no output is printed for more than global_timeout seconds, startpar will flush the buffer of
the script with the oldest output. Afterwards it will only print output of this script until it is finished.
The -M option switches startpar into a make(1) like behaviour. This option takes three different arguments: boot, start, and stop for
reading .depend.boot or .depend.start or .depend.stop respectively in the directory /etc/init.d/. By scanning the boot and runlevel direc-
tories in /etc/init.d/ it then executes the appropriate scripts in parallel.
FILES
/etc/init.d/.depend.boot
/etc/init.d/.depend.start
/etc/init.d/.depend.stop
SEE ALSO
init.d(7), insserv(8), startproc(8).
COPYRIGHT
2003,2004 SuSE Linux AG, Nuernberg, Germany.
2007 SuSE LINUX Products GmbH, Nuernberg, Germany.
AUTHOR
Michael Schroeder <mls@suse.de>
Takashi Iwai <tiwai@suse.de>
Werner Fink <werner@suse.de>
Jun 2003 STARTPAR(8)