04-28-2012
ifconfig hme0 plumb not working
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi...
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
4. Solaris
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies
5. UNIX for Dummies Questions & Answers
I have sun solaris 9 installed but I have the interface configured to hme1 instead of hme0, our default value.
Is there a way where i can rename the existing/working hme1 to hme0...?
I want to showup the hmeo up if i say ifconfig -a..
rite now i see the hme1 up..
please advice if possible... (4 Replies)
Discussion started by: tintedwindow
4 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. Solaris
Hi All,
I logged into a sun microsystems server box, using both a vnc session and a ssh session. I am able to use "ifconfig -a" in a ssh session, but the same on a vnc session says that its a invalid command. how is this possible, when i am logging into the same box through two different... (4 Replies)
Discussion started by: pardhuhere
4 Replies
8. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
9. Solaris
Ultra E150 Solaris 2.5.1 Oracle server. was working fine, then started losing network connection. I can see in messages file that it was complaining about another device using its ip address. Though not any longer, though I wonder if that was a red herring. My IT guys have now re-reserved its ip... (29 Replies)
Discussion started by: AlSmith1964
29 Replies
10. Solaris
Hello Folks, can anyone please help me with this ?! :wall:
I'm using Solaris 10 with Sun V880 which has two Networks Interfaces, a Fiber (ge0) and a cooper (eri0).
The eri0 is working great but when I try to plumb the ge0 interface ...
# ifconfig ge0 plumb
ifconfig: cannot open link... (18 Replies)
Discussion started by: pxb368@motorola
18 Replies
LEARN ABOUT OPENSOLARIS
whois
whois(1) User Commands whois(1)
NAME
whois - Internet user name directory service
SYNOPSIS
whois [-h host] identifier
DESCRIPTION
whois searches for an Internet directory entry for an identifier which is either a name (such as ``Smith'') or a handle (such as ``SRI-
NIC''). To force a name-only search, precede the name with a period; to force a handle-only search, precede the handle with an exclamation
point.
To search for a group or organization entry, precede the argument with * (an asterisk). The entire membership list of the group will be
displayed with the record.
You may of course use an exclamation point and asterisk, or a period and asterisk together.
EXAMPLES
Example 1 Using The whois Command
The command:
example% whois Smith
looks for the name or handle SMITH.
The command:
example% whois !SRI-NIC
looks for the handle SRI-NIC only.
The command:
example% whois .Smith, John
looks for the name JOHN SMITH only.
Adding ... to the name or handle argument will match anything from that point; that is, ZU ... will match ZUL, ZUM, and so on.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWrcmdc |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
SunOS 5.11 6 Nov 2000 whois(1)