Sponsored Content
Full Discussion: port state issue
Special Forums IP Networking port state issue Post 302611627 by kuba7 on Friday 23rd of March 2012 08:11:10 AM
Old 03-23-2012
I do not understand could You help?

I would like to check on which router/server/firewall the connection to given port is blocked.
How can I do it?

I tried to use traceroute, with wrong assumptions I guess.
 

10 More Discussions You Might Find Interesting

1. HP-UX

PXE boot port issue

Hi,all: I want to boot an IA unix box from network, I am sure I set the DHCP and boot server, but it still failed ! It says : Client MAC Address: 00 18 FE 28 91 82 .....- PXE-E16: Valid PXE offer not received. Load of Core LAN Gb A failed: Not Found I use the nettl command to trace the UDP... (0 Replies)
Discussion started by: bluepluto
0 Replies

2. Solaris

Serial port issue

Hi, I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port. When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies

3. UNIX for Dummies Questions & Answers

Hitting with custom port in CLOSE_WAIT state for long time in solaris 10

Hi, Occasionally I am getting the port state in CLOSE_WAIT for long time in the solaris server. I am not sure is it application problem or not. Because we are using port 9009 for Tomcat process in our web application, some time when I start the application, the port 9009 is in CLOSE_WAIT... (0 Replies)
Discussion started by: mgmk.84
0 Replies

4. AIX

Port hang issue in AIX Version 5.3

On AIX platform we are having Weblogic 8.1 as the middleware for an application. The application is deployed in Weblogic on AIX platform and the server is having 2 dedicated listening ports for any incoming requests. Output for netstat -an command for the port 30001 is as follows:- tcp4... (7 Replies)
Discussion started by: subharai
7 Replies

5. Programming

Locking issue with serial port

Hi, In my application,I need to monitor the devices connected through serial port in solaris sparc 9 OS.I used c and java code for it and I am able to do the same but the problem comes when I restart the system and the open my application and try to monitor it.but I m unable to monitor the... (2 Replies)
Discussion started by: smartgupta
2 Replies

6. HP-UX

FC port issue

I'm facing some strange HP-UX behavior. I have a small SAN with one HP server, two Cisco SAN switches and one HP tape library connected. When I issues port reset, syslog shows the following: Oct 15 07:34:51 terumos-bckp-srv2 vmunix: Target path (class=tgtpath, instance=12) has gone online. ... (2 Replies)
Discussion started by: Sapfeer
2 Replies

7. Red Hat

HP Data Protector port 5555 issue

Dear All, I have my HP Data Protector installed on the backup server. I want to connect this backup server with the client server through telnet port 5555 like below telnet < ipaddress of client> 5555 But when I try like this , it says ...Connection refused ...unable to connect to... (0 Replies)
Discussion started by: jegaraman
0 Replies

8. AIX

Open firmware state to running state

Hi Admins, I am having a whole system lpar in open firmware state on HMC. How can I bring it to running state ? Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies

9. HP-UX

After adding new iscsi target port, still the session state of that target port is showing offline

Hi, I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result ... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies

10. IP Networking

Port forwarding issue

hi guys i have a simple question ! i have two ips . a valid and internal(172.16.11.2) i want to use port forwarding to forward any request to valid IP port 8001 to internal ip port 80 . i use this rule : sysctl -w net.ipv4.ip_forward=1 iptables -t nat -A PREROUTING -p tcp... (1 Reply)
Discussion started by: mhs
1 Replies
BLACKHOLE(4)						   BSD Kernel Interfaces Manual 					      BLACKHOLE(4)

NAME
blackhole -- a sysctl(8) MIB for manipulating behaviour in respect of refused TCP or UDP connection attempts SYNOPSIS
sysctl net.inet.tcp.blackhole[=[0 | 1 | 2]] sysctl net.inet.udp.blackhole[=[0 | 1]] DESCRIPTION
The blackhole sysctl(8) MIB is used to control system behaviour when connection requests are received on TCP or UDP ports where there is no socket listening. Normal behaviour, when a TCP SYN segment is received on a port where there is no socket accepting connections, is for the system to return a RST segment, and drop the connection. The connecting system will see this as a ``Connection refused''. By setting the TCP blackhole MIB to a numeric value of one, the incoming SYN segment is merely dropped, and no RST is sent, making the system appear as a blackhole. By setting the MIB value to two, any segment arriving on a closed port is dropped without returning a RST. This provides some degree of protection against stealth port scans. In the UDP instance, enabling blackhole behaviour turns off the sending of an ICMP port unreachable message in response to a UDP datagram which arrives on a port where there is no socket listening. It must be noted that this behaviour will prevent remote systems from running traceroute(8) to a system. The blackhole behaviour is useful to slow down anyone who is port scanning a system, attempting to detect vulnerable services on a system. It could potentially also slow down someone who is attempting a denial of service attack. WARNING
The TCP and UDP blackhole features should not be regarded as a replacement for firewall solutions. Better security would consist of the blackhole sysctl(8) MIB used in conjuction with one of the available firewall packages. This mechanism is not a substitute for securing a system. It should be used together with other security mechanisms. SEE ALSO
ip(4), tcp(4), udp(4), ipf(8), ipfw(8), pfctl(8), sysctl(8) HISTORY
The TCP and UDP blackhole MIBs first appeared in FreeBSD 4.0. AUTHORS
Geoffrey M. Rehmet BSD
January 1, 2007 BSD
All times are GMT -4. The time now is 05:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy