ok here is what i do and get:
# mount /dev/sd6a /cdrom
mount /dev/sd6a write-protected
ok so what do i do its a external cdrom and its on scsi number 6. its a SparcSTATION 2. we're trying to put red hat sparc 6.2 on it but it wont boot. i am about to take the hard drives out and install it a... (8 Replies)
I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Hi all ,
I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows :
cleaning up preexisting install client "XXXXXXX"
removing XXXXXXXfrom bootparams
removing /etc/bootparams, since it is... (14 Replies)
Hello everyone,
I tried to install solaris 10 using the command # boot net - install.
I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following:
... (7 Replies)
Hello,
First i'm Dutch, and my English is not very well. Sorry. :D
I have got a Sun Microsystems Ultra 3D (with SPARC processor). The file must be burned to a DVD. And my computer can onley read a cd.
How to get Solaris 10 on a few cds?
Please help me.
Thanks a lot..
Greets. (21 Replies)
Good day everyone,
I am trying to install some new senmail patch on my Solaris 10 system.
I know the cdrom for my CP3260 blade servers in my rack worked for the last patches installed. However, when I went to copy from the .tar file from the cdrom to the /tmp. I received an error cannot... (2 Replies)
I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems.
Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86?
Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Hello,
I am following the HPUX 11.31 install/update guide and I am trying to install "Update-UX" from the installation media. I put the CD into the drive, and I am trying to mount the device. The instructions state:Find the DVD-ROM device file name:
ioscan -C disk -f -n -k | more
A typical... (5 Replies)
I want to have a bootable DVD that will perform a jumpstart install of Solaris 10 x86 I've mainly used JumpStart DVD (with Solaris flash archive) for x86 platform as a reference, and I used the sysidcfg, profile, rules, etc. from a working jumpstart server. For the life of me, though, I cannot... (1 Reply)
Discussion started by: jnojr
1 Replies
LEARN ABOUT OSX
locale::codes::currency
Locale::Codes::Currency(3pm) Perl Programmers Reference Guide Locale::Codes::Currency(3pm)NAME
Locale::Codes::Currency - standard codes for currency identification
SYNOPSIS
use Locale::Codes::Currency;
$curr = code2currency('usd'); # $curr gets 'US Dollar'
$code = currency2code('Euro'); # $code gets 'eur'
@codes = all_currency_codes();
@names = all_currency_names();
DESCRIPTION
The "Locale::Codes::Currency" module provides access to standard codes used for identifying currencies and funds, such as those defined in
ISO 4217.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 4217
three-letter codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying currencies. A code set may be specified using either a name, or a
constant that is automatically exported by this module.
For example, the two are equivalent:
$curr = code2currency('usd','alpha');
$curr = code2currency('usd',LOCALE_CURR_ALPHA);
The codesets currently supported are:
alpha, LOCALE_CURR_ALPHA
This is a set of three-letter (uppercase) codes from ISO 4217 such as EUR for Euro.
Two of the codes specified by the standard (XTS which is reserved for testing purposes and XXX which is for transactions where no
currency is involved) are omitted.
This is the default code set.
num, LOCALE_CURR_NUMERIC
This is the set of three-digit numeric codes from ISO 4217.
ROUTINES
code2currency ( CODE [,CODESET] )
currency2code ( NAME [,CODESET] )
currency_code2code ( CODE ,CODESET ,CODESET2 )
all_currency_codes ( [CODESET] )
all_currency_names ( [CODESET] )
Locale::Codes::Currency::rename_currency ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::Currency::add_currency ( CODE ,NAME [,CODESET] )
Locale::Codes::Currency::delete_currency ( CODE [,CODESET] )
Locale::Codes::Currency::add_currency_alias ( NAME ,NEW_NAME )
Locale::Codes::Currency::delete_currency_alias ( NAME )
Locale::Codes::Currency::rename_currency_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::Currency::add_currency_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::Currency::delete_currency_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iso.org/iso/support/currency_codes_list-1.htm
The ISO 4217 data.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 1997-2001 Canon Research Centre Europe (CRE).
Copyright (c) 2001 Michael Hennecke
Copyright (c) 2001-2010 Neil Bowers
Copyright (c) 2010-2012 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.2 2012-10-11 Locale::Codes::Currency(3pm)