ok here is what i do and get:
# mount /dev/sd6a /cdrom
mount /dev/sd6a write-protected
ok so what do i do its a external cdrom and its on scsi number 6. its a SparcSTATION 2. we're trying to put red hat sparc 6.2 on it but it wont boot. i am about to take the hard drives out and install it a... (8 Replies)
I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Hi all ,
I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows :
cleaning up preexisting install client "XXXXXXX"
removing XXXXXXXfrom bootparams
removing /etc/bootparams, since it is... (14 Replies)
Hello everyone,
I tried to install solaris 10 using the command # boot net - install.
I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following:
... (7 Replies)
Hello,
First i'm Dutch, and my English is not very well. Sorry. :D
I have got a Sun Microsystems Ultra 3D (with SPARC processor). The file must be burned to a DVD. And my computer can onley read a cd.
How to get Solaris 10 on a few cds?
Please help me.
Thanks a lot..
Greets. (21 Replies)
Good day everyone,
I am trying to install some new senmail patch on my Solaris 10 system.
I know the cdrom for my CP3260 blade servers in my rack worked for the last patches installed. However, when I went to copy from the .tar file from the cdrom to the /tmp. I received an error cannot... (2 Replies)
I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems.
Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86?
Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Hello,
I am following the HPUX 11.31 install/update guide and I am trying to install "Update-UX" from the installation media. I put the CD into the drive, and I am trying to mount the device. The instructions state:Find the DVD-ROM device file name:
ioscan -C disk -f -n -k | more
A typical... (5 Replies)
I want to have a bootable DVD that will perform a jumpstart install of Solaris 10 x86 I've mainly used JumpStart DVD (with Solaris flash archive) for x86 platform as a reference, and I used the sysidcfg, profile, rules, etc. from a working jumpstart server. For the life of me, though, I cannot... (1 Reply)
Discussion started by: jnojr
1 Replies
LEARN ABOUT MOJAVE
locale::codes::langext5.18
Locale::Codes::LangExt(3pm) Perl Programmers Reference Guide Locale::Codes::LangExt(3pm)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangExt(3pm)
02-14-2012
