01-05-2012
Perhaps you should contact the supplier........?
9 More Discussions You Might Find Interesting
1. Solaris
To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still... (3 Replies)
Discussion started by: cstovall
3 Replies
2. IP Networking
I have a linksys router BEFSR41. I am trying to connect two network..
one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95.
In the configuration LAN ip address by default it 192.168.1.1
If I define LAN IP to... (0 Replies)
Discussion started by: ajnabi
0 Replies
3. IP Networking
I have an SGI running Irix 6.5 and I am trying to connect it to my home network that consists of two Windows PC's (Win 98SE and Win 2000) plus the SGI all connected to a Linksys router which is connected to my DSL modem. My ISP is Verizon DSL (Dynamic IP addressing.)
All network lights are... (3 Replies)
Discussion started by: mdbanas
3 Replies
4. IP Networking
I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I... (10 Replies)
Discussion started by: nicomen
10 Replies
5. Shell Programming and Scripting
I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below).
http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127
Here is my wget command:
wget --http-user=xyz --http-password=xyz... (1 Reply)
Discussion started by: mike909
1 Replies
6. UNIX for Dummies Questions & Answers
Hello I am new to Ubuntu and I have a quick question about router settings. When I connect directly to my cable Internet ubuntu works fine. But when I connect it to my router I can't get connectivity. I am using ubuntu 9.04 and am using D-link DI-604 router. I have reset both my router and modem... (0 Replies)
Discussion started by: jae99
0 Replies
7. UNIX for Dummies Questions & Answers
I set up remote printing on a clients Unix server to my Windows XP USB printer. My USB printer is connected directly to my PC (no print server and no network input on printer). With my Win XP PC connected to my cable modem (without the router), i can do
lp -dhp842c /etc/hosts and it prints. I... (7 Replies)
Discussion started by: jmhohne
7 Replies
8. IP Networking
Does anyone know if this router can restrict incoming traffic to specific IP addresses. There does not seem to be any information on Cisco's web site any more.
ie Only 209.123.123.123 is allowed access to port 9100, which is redirected to 192.168.1.100 (1 Reply)
Discussion started by: jgt
1 Replies
9. UNIX for Dummies Questions & Answers
I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet.
When I switch back to "Automatically obtain IP address" ..then I can get on the internet.
Can comeone help with this. (2 Replies)
Discussion started by: FrankOscar
2 Replies
BWI(4) BSD Kernel Interfaces Manual BWI(4)
NAME
bwi -- Broadcom BCM43xx IEEE 802.11b/g wireless network driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device bwi
device wlan
device wlan_amrr
device firmware
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_bwi_load="YES"
DESCRIPTION
The bwi driver provides support for Broadcom BCM43xx based PCI/CardBus network adapters.
It supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on configur-
ing this device, see ifconfig(8).
This driver requires firmware to be loaded before it will work. The ports/net/bwi-firmware-kmod port needs to be installed before
ifconfig(8) will work.
HARDWARE
The bwi driver supports Broadcom BCM43xx based wireless devices, including:
Card Chip Bus Standard
Apple Airport Extreme BCM4306 PCI b/g
Apple Airport Extreme BCM4318 PCI b/g
ASUS WL-138g BCM4318 PCI b/g
Buffalo WLI-CB-G54S BCM4318 CardBus b/g
Buffalo WLI-PCI-G54S BCM4306 PCI b/g
Compaq R4035 onboard BCM4306 PCI b/g
Dell Wireless 1470 BCM4318 Mini PCI b/g
Dell Truemobile 1400 BCM4309 Mini PCI b/g
HP nx6125 BCM4319 PCI b/g
Linksys WPC54G Ver 3 BCM4318 CardBus b/g
Linksys WPC54GS Ver 2 BCM4318 CardBus b/g
TRENDnet TEW-401PCplus BCM4306 CardBus b/g
US Robotics 5411 BCM4318 CardBus b/g
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev bwi0 inet 192.168.0.20
netmask 0xffffff00
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev bwi0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev bwi0 ssid my_net
wepmode on wepkey 0x1234567890 weptxkey 1 up
SEE ALSO
arp(4), cardbus(4), intro(4), pci(4), wlan(4), wlan_amrr(4), ifconfig(8), wpa_supplicant(8)
HISTORY
The bwi driver first appeared in FreeBSD 8.0.
AUTHORS
The bwi driver was written for DragonFly BSD by Sepherosa Ziehau and subsequently ported to FreeBSD.
BUGS
Some card based on the BCM4306 and BCM4309 chips do not work properly on channel 1, 2 and 3.
BSD
May 16, 2009 BSD