01-05-2012
Linksys router question
Hi
I have very basic network settings in my home. Cable connected to my Linksys Wireless G router. My wife and I connect to that using our laptop.
Yes. I did enable encryption to connect. Also my wireless printer is connected to that.
For some reason, last night around 12:30 AM, the printer acted like it was going to print. Then it didn't print any thing. Again it did that one hour later.
My question, is it possible some one hacked into my Linksys router? The wireless printer never did that before?
Thanks.
9 More Discussions You Might Find Interesting
1. Solaris
To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still... (3 Replies)
Discussion started by: cstovall
3 Replies
2. IP Networking
I have a linksys router BEFSR41. I am trying to connect two network..
one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95.
In the configuration LAN ip address by default it 192.168.1.1
If I define LAN IP to... (0 Replies)
Discussion started by: ajnabi
0 Replies
3. IP Networking
I have an SGI running Irix 6.5 and I am trying to connect it to my home network that consists of two Windows PC's (Win 98SE and Win 2000) plus the SGI all connected to a Linksys router which is connected to my DSL modem. My ISP is Verizon DSL (Dynamic IP addressing.)
All network lights are... (3 Replies)
Discussion started by: mdbanas
3 Replies
4. IP Networking
I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I... (10 Replies)
Discussion started by: nicomen
10 Replies
5. Shell Programming and Scripting
I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below).
http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127
Here is my wget command:
wget --http-user=xyz --http-password=xyz... (1 Reply)
Discussion started by: mike909
1 Replies
6. UNIX for Dummies Questions & Answers
Hello I am new to Ubuntu and I have a quick question about router settings. When I connect directly to my cable Internet ubuntu works fine. But when I connect it to my router I can't get connectivity. I am using ubuntu 9.04 and am using D-link DI-604 router. I have reset both my router and modem... (0 Replies)
Discussion started by: jae99
0 Replies
7. UNIX for Dummies Questions & Answers
I set up remote printing on a clients Unix server to my Windows XP USB printer. My USB printer is connected directly to my PC (no print server and no network input on printer). With my Win XP PC connected to my cable modem (without the router), i can do
lp -dhp842c /etc/hosts and it prints. I... (7 Replies)
Discussion started by: jmhohne
7 Replies
8. IP Networking
Does anyone know if this router can restrict incoming traffic to specific IP addresses. There does not seem to be any information on Cisco's web site any more.
ie Only 209.123.123.123 is allowed access to port 9100, which is redirected to 192.168.1.100 (1 Reply)
Discussion started by: jgt
1 Replies
9. UNIX for Dummies Questions & Answers
I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet.
When I switch back to "Automatically obtain IP address" ..then I can get on the internet.
Can comeone help with this. (2 Replies)
Discussion started by: FrankOscar
2 Replies
enable(1) User Commands enable(1)
NAME
enable, disable - enable/disable LP printers
SYNOPSIS
/usr/bin/enable printer...
/usr/bin/disable [-c | -W] [ -r [reason]] printer...
DESCRIPTION
The enable command activates printers, enabling them to print requests submitted by the lp command. enable must be run on the printer
server.
The disable command deactivates printers, disabling them from printing requests submitted by the lp command. By default, any requests that
are currently printing on printer will be reprinted in their entirety either on printer or another member of the same class of printers.
The disable command must be run on the print server.
Use lpstat -p to check the status of printers.
enable and disable only effect queueing on the print server's spooling system. Executing these commands from a client system will have no
effect on the server.
OPTIONS
The following options are supported for use with disable:
-c Cancels any requests that are currently printing on printer. This option cannot be used with the -W option. If the printer
is remote, the -c option will be silently ignored.
-W Waits until the request currently being printed is finished before disabling printer. This option cannot be used with the
-c option. If the printer is remote, the -W option will be silently ignored.
-r [reason] Assigns a reason for the disabling of the printer(s). This reason applies to all printers specified. This reason is
reported by lpstat -p. Enclose reason in quotes if it contains blanks. The default reason is "unknown reason" for the
existing printer, and "new printer" for a printer added to the system but not yet enabled.
OPERANDS
The following operand is supported for both enable and disable:
printer The name of the printer to be enabled or disabled. Specify printer using atomic name. See printers.conf(4) for information
regarding the naming conventions for atomic names.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
FILES
/var/spool/lp/* LP print queue.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWpcu |
+-----------------------------+-----------------------------+
|CSI |enabled |
+-----------------------------+-----------------------------+
SEE ALSO
lp(1), lpstat(1), printers.conf(4), attributes(5)
SunOS 5.10 9 Sep 1996 enable(1)