12-29-2011
Multiple interface same network
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Dummies Questions & Answers
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Discussion started by: 98_1LE
3 Replies
3. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
4. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT MOJAVE
tc-route
Route classifier in tc(8) Linux Route classifier in tc(8)
NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO
tc(8), ip-route(8)
iproute2 21 Oct 2015 Route classifier in tc(8)