Sponsored Content
Full Discussion: Network Interface -- Solaris
Operating Systems Solaris Network Interface -- Solaris Post 302585370 by jegaraman on Wednesday 28th of December 2011 08:07:33 AM
Old 12-28-2011
Hi Rajesh and all.

yes there is some performance issue of slowness.. I do not find any other issues.

Since I did the performance monitoring for this server. I find no other deviations.

I have a doubt in this.

kindlly let me know if you have any issues on this.

Rgds
Rj
 

9 More Discussions You Might Find Interesting

1. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

2. Solaris

Solaris 9 on x86- Can't detect network interface

Hi All, I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot. While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies

3. Solaris

Determine Solaris box network interface?

Given a new Solaris box, with a fresh, unconfigured install on it, how does one figure out what kind of network interface it has (bge,le, hme, etc)? (8 Replies)
Discussion started by: akbar
8 Replies

4. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

5. Solaris

What are the kernel parameter of network interface in Solaris?

Hi gurus Could anybody tell me that what are the kernal parameter of network interface in solaris Regards (3 Replies)
Discussion started by: girish.batra
3 Replies

6. Solaris

Solaris Network Interface and USB Drive issues

Hi I had installed Sun Solaris 10 on my dell vostro 1400.Problem is iam unable to mount the usb drives as there was no detections at all.And also iam unable to find my network interface or iam not able to install the network card. If try to type ifconfig -a It is showing only loop back... (4 Replies)
Discussion started by: testerindia25
4 Replies

7. Solaris

Getting Network Interface details in solaris

Hi, /sbin/ifconfig -a when i login as guest user , output like below, lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet... (5 Replies)
Discussion started by: forumguest
5 Replies

8. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

9. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
certmonger(1)						      General Commands Manual						     certmonger(1)

NAME
certmaster-getcert SYNOPSIS
certmaster-getcert request [options] certmaster-getcert resubmit [options] certmaster-getcert start-tracking [options] certmaster-getcert stop-tracking [options] certmaster-getcert list [options] certmaster-getcert list-cas [options] DESCRIPTION
The certmaster-getcert tool issues requests to a org.fedorahosted.certmonger service on behalf of the invoking user. It can ask the ser- vice to begin enrollment, optionally generating a key pair to use, it can ask the service to begin monitoring a certificate in a specified location for expiration, and optionally to refresh it when expiration nears, it can list the set of certificates that the service is already monitoring, or it can list the set of CAs that the service is capable of using. If no command is given as the first command-line argument, ipa-getcert will print short usage information for each of its functions. The certmaster-getcert tool behaves identically to the generic getcert tool when it is used with the -c certmaster option. BUGS
Please file tickets for any that you find at https://fedorahosted.org/certmonger/ SEE ALSO
certmonger(8) getcert-list(1) getcert-list-cas(1) getcert-request(1) getcert-resubmit(1) getcert-start-tracking(1) getcert-stop-tracking(1) certmonger-certmaster-submit(8) certmonger-ipa-submit(8) certmonger_selinux(8) certmonger Manual 23 November 2009 certmonger(1)
All times are GMT -4. The time now is 06:17 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy