12-28-2011
Hi Rajesh and all.
yes there is some performance issue of slowness.. I do not find any other issues.
Since I did the performance monitoring for this server. I find no other deviations.
I have a doubt in this.
kindlly let me know if you have any issues on this.
Rgds
Rj
9 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. Solaris
Hi All,
I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot.
While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies
3. Solaris
Given a new Solaris box, with a fresh, unconfigured install on it, how does one figure out what kind of network interface it has (bge,le, hme, etc)? (8 Replies)
Discussion started by: akbar
8 Replies
4. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
5. Solaris
Hi gurus
Could anybody tell me that what are the kernal parameter of network interface in solaris
Regards (3 Replies)
Discussion started by: girish.batra
3 Replies
6. Solaris
Hi
I had installed Sun Solaris 10 on my dell vostro 1400.Problem is iam unable to mount the usb drives as there was no detections at all.And also iam unable to find my network interface or iam not able to install the network card.
If try to type ifconfig -a
It is showing only loop back... (4 Replies)
Discussion started by: testerindia25
4 Replies
7. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
8. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
9. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
LEARN ABOUT REDHAT
webserver
WEBSERVER(1) mrtg WEBSERVER(1)
NAME
webserver - hints for web server configuration
SYNOPSIS
If you want people to actually see the results of your network monitoring efforts you will need a webserver.
This document lists some configuration hints for webservers. Contributions welcome.
APACHE
Configuring mod_expire
A big issue with mrtg monitoring data is the expiery time. All these nice graphs you can create are only valid for a short time. If you
do not take special action some webbrowsers will not notice this and you may end up with people seeing old data because of caching issues.
The apache module mod_expire allows you to setup special expiery properties for individual file.
Here is an example for how this may look for an mrtg web directory. The configuration directives can be stored into a .htaccess file.
############################################################
# Example .htaccess for use with apache-1.2 and mod_expire.
# (mod_expire come with apache-1.2 but you have to explicitly
# activate it when compiling the httpd ...)
#############################################################
#
<Files "*-day.png">
ExpiresActive On # enable expirations
# five minutes
ExpiresDefault M300
</Files>
<Files "*-week.png">
ExpiresActive On
ExpiresDefault M1800
</Files>
<Files "*-month.png">
ExpiresActive On
ExpiresDefault M7200
</Files>
<Files "*-year.png">
ExpiresActive On
ExpiresDefault M86400
</Files>
<Files "*.html">
ExpiresActive On
ExpiresDefault M300
</Files>
# index.html is not automatically generated
<Files "index.html">
ExpiresActive Off
</Files>
AUTHOR
Unknown
3rd Berkeley Distribution 2.9.17 WEBSERVER(1)