Sponsored Content
Operating Systems AIX How to set 4 SEA on single VIOS Post 302572824 by nagarjunatula on Friday 11th of November 2011 07:45:21 AM
Old 11-11-2011
hi polar,
what is ur server model?
depends upon the model we have to configure.if it is power6 520 then k.
is ur server is managed through hmc?
if it is connected, select the server and go to hardware information.tjhere you will locate the physical ethernet ports, then select the port and configure it.set the promiscous mode for the port which u have selected.
 

10 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

Call single function multiple times diff set of parameters

Okay, not sure if it can be done, I would think it could be done and I'm just having a hard time with it. fun_close_wait(){ ipVar="${1} ${2}" portVar=`cat "${5}" | cut -d' ' -f 1` for ip in $ipVar do for port in $portVar do netstatVar=`netstat -n | grep... (4 Replies)
Discussion started by: cbo0485
4 Replies

2. AIX

VIOS SEA on LHEA doesn't work

I am trying to create a SEA on a LHEA port and it gives me error lsdev -Cc adapter: ent0 logical host ethernet port (l-hea) ent1 virtual I/O ethernet adapter mkvdev -sea ent0 -vadapter ent1 -default ent1 -defaultid 199 method error (/usr/lib/methods/cfgsea): Failed to configure SEA... (0 Replies)
Discussion started by: filosophizer
0 Replies

3. AIX

VIOS SEA Creation

Hi Guys, I'm getting the below error while trying to create a SEA adapter in VIOS $ mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1 ... (4 Replies)
Discussion started by: kkeng808
4 Replies

4. AIX

SEA

Hi all, I set up the following configuration on my system: - An LPar with a virtual adapter, first one with a vlan id=703 and id port=13. - The first adapter have to connect to a VIOS in which i configured an SEA. So, the VA is set up on interface ent2, SEA on ent29 (by linking a... (0 Replies)
Discussion started by: idro
0 Replies

5. Linux

Set password in single command

Hi, Can we set password for linux in non-interactive mode. I didn't find suitable option for this in man page. If we wnter "passwd" command, it will tell "Enter password" and "Re-enter password". i wanted to run this step in a script, and i don't want to use "expect" so i am looking for a single... (8 Replies)
Discussion started by: successlin
8 Replies

6. AIX

Configure VIOS SEA w. load sharing

I am trying to install a VIOS pair with a load-sharing SEA adapter, following this recipe from Developerworks. Without load-sharing everything went fine and worked as expected, but somehow i am a bit lost and the first tries with "ha_mode=sharing" didn't work at all. Here is the situation: I... (6 Replies)
Discussion started by: bakunin
6 Replies

7. AIX

VIOS IP address - separate vlan for vios servers ?

Hello, Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2. What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies

8. AIX

SEA configuration

i want configure a SEA over my vios , i have a message error : Method error (/usr/lib/methods/cfgsea): Failed to configure SEA with return code 1 and SEA-specific error code 10: Detailed info: Setting real adapter ent1 in promiscuous mode failed... (5 Replies)
Discussion started by: hedou
5 Replies

9. AIX

SEA to standby

hello, what will happen if i try to move sea of my 1 vio server to standby( using chdev command), when sea of other vio server is already in standby mode? (1 Reply)
Discussion started by: amvineeth
1 Replies

10. AIX

VIOS entstat versus seastat for SEA

Hello, I found that the packet counts given by entstat -d SEA is not the same as the total of the packet counts given by seastat -d SEA for the same interval of time. Do anyone have an explanation for the difference. We recently got a recommendation that the throughput on an SEA should not... (5 Replies)
Discussion started by: N8R
5 Replies
cachemgr.cgi(8) 					      System Manager's Manual						   cachemgr.cgi(8)

NAME
cachemgr.cgi - squid HTTP proxy manager interface SYNOPSIS
http://your.server/cgi-bin/cachemgr.cgi DESCRIPTION
The cache manager (cachemgr.cgi) is a CGI utility for displaying statistics about the Squid HTTP proxy process as it runs. The cache man- ager is a convenient way to manage the cache and view statistics without logging into the server. FILES
./cachemgr.conf @DEFAULT_CACHEMGR_CONFIG@ The access configuration file defining which Squid servers may be managed via this cachemgr.cgi program. Each line specifies a server:port followed by an optional description The server name may contain shell wildcard characters such as *, [] etc. A quick selection dropdown menu is automatically con- structed from the simple server names. Specifying :port is optional. If not specified then the default proxy port is assumed. :* or :any matches any port on the target server. SECURITY
cachemgr.cgi calls the requested server on the requested port using HTTP and returns a formatted version of the response. To avoid abuse it is recommended to configure your web server to restrict access to the cachemgr.cgi program. Configuration examples for many common web servers can be found in the Squid FAQ. SEE ALSO
squid(8) The Squid FAQ, Chapter 9 The Cache Manager Squid Web Proxy 3.1.20 cachemgr.cgi(8)
All times are GMT -4. The time now is 07:04 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy