10-31-2011
This is not UNIX 5.3 but AIX 5.3
. Moving it to the AIX sub forum.
Did you run
cfgmgr after you assigned that drive to the LPAR?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Following the below info:
----------------------------------------------------------------------------------
# SYNTAX: /dev/rmt/<unit number><density>
· Density: l, m, h, u/c (low, medium, high, ultra/compressed, respectively)
· BSD behavior: (optional) b
· no rewind: (optional) n
· For... (5 Replies)
Discussion started by: guest100
5 Replies
2. Solaris
hi all ,
i have just installed solris 9 on a sun 280R ,and i have appleid the recommended patches .
after the installation i have found that /dev/rmt/ directory is empty , i thought that was normal , so i attached my DDS4 external tape drive and treid :
devfsadm -C
devfsadm -v
reboot --... (1 Reply)
Discussion started by: ppass
1 Replies
3. AIX
Hi.
After the shutdown for SWIFT Alliance Server, tape backup process will be done. Unfortunately, I encountered this error message when I performed the database tape backup. The error was "/dev/rmt 0.1 block size is 0; variable; must be 1024 fixed. Consider reconfiguration through 'chdev'... (2 Replies)
Discussion started by: MariaLuisa
2 Replies
4. Solaris
Hi Guys,
I a newbie in Unix environment. I need a help to detect my external SCSI tape drive. I tried with command drvconfig;devlinks;tapes.. but when I go to /dev/rmt/, the directory is still empty.
I also tried with add_drv -v st but I'm getting this message
# add_drv -v st
exit... (8 Replies)
Discussion started by: akuslive
8 Replies
5. AIX
Hi all,
Sometimes, when I reboot my AIX server, my tape drive /dev/rmt# assignments change. This creates some tedious TSM work prior to and after a reboot of the server.
Is there a way to ensure that the /dev/rmt# assignments come up the same every time?
Thanks (5 Replies)
Discussion started by: jwholey
5 Replies
6. UNIX for Dummies Questions & Answers
Hi folks,
I am trying to learn Unix based in Linux...
In Linux, in /Dev are files related to cards, mouse, etc..
how about Unix?
What is the difference between /Dev and /Devices?
Thanks,
Fernanda (0 Replies)
Discussion started by: ffpradella
0 Replies
7. Solaris
I have an HP Proliant DL380 with Intel Processors that I recently loaded Solaris 10 with latest patches on it. I'm trying to do a ufsdump to an HP DAT 40 tape drive via SCSI, but I can't get it to do anything because /dev/rmt is empty. I've tried the following with luck:
touch /reconfigure,... (7 Replies)
Discussion started by: cvaughn
7 Replies
8. Hardware
# mt stat
HP DDS-4 DAT (Sun) tape drive:
sense key(0x0)= No Additional Sense residual= 0 retries= 0
file no= 0 block no= 0
mt -f /dev/rmt/0mn erase
/dev/rmt/0mn: write protected or reserved.
Getting error while ufsdump ....
--- Dumping / to /dev/rmt/0mn ---
DUMP: Date... (1 Reply)
Discussion started by: vickyingle5
1 Replies
9. Solaris
# mt stat
HP DDS-4 DAT (Sun) tape drive:
sense key(0x0)= No Additional Sense residual= 0 retries= 0
file no= 0 block no= 0
mt -f /dev/rmt/0mn erase
/dev/rmt/0mn: write protected or reserved.
Getting error while ufsdump ....
--- Dumping / to /dev/rmt/0mn ---
DUMP: Date... (5 Replies)
Discussion started by: vickyingle5
5 Replies
10. HP-UX
Hi,
In our HP-UX B.11.11. I could not find dev/urandom and dev/random
Are all pseudo-devices implemented as device drivers, or in need to run /configure some package to install the package to have dev/urandom.
Please help (4 Replies)
Discussion started by: rashi
4 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)