Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Changed disk controller -> drops into GRUB?!
Operating Systems Solaris Changed disk controller -> drops into GRUB?! Post 302566615 by otheus on Thursday 20th of October 2011 05:01:16 PM
Old 10-20-2011
The grub online docs will pave the way. If you got into grub, it's a good thing. You just have to ask grub to find the kernels that are installed and it will find them. Reply if you are still stumped after some research and trial-error
 

9 More Discussions You Might Find Interesting

1. Solaris

Controller target disk?

Hi, I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below: /pci@8,600000/SUNW,qlc@2 LiD HA LUN --- Port WWN --- ----- Disk description ----- 0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies

2. SCO

Warning HD: no root disk controller was found

hi... i hav a problem to install sco unix while installing sco unix 5.0.5 in acer altos with hardware raid am getting error "Warning HD: no root disk controller was found system error 5: while getting fs type flushing controller: DAC960PRL cache done." i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies

3. HP-UX

[Joy Share] - Replace an unknown status controller on HP FC60 disk array

Replace an unknown status controller on HP FC60 disk array Author:JoyOnline JoyChangLu@gmail.com Trouble description: The users detected that the status of controller at A is unknown. Analysis and diagnostic: Physical observed all leds on enclosure of disk array is normal. The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies

4. SCO

SCO 5.0.7 no root disk controller found error during install

I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd. I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies

5. Solaris

Help needed to find out the disk controller for veritas disks

hi all i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output # vxdisk list DEVICE TYPE DISK GROUP STATUS c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies

6. SCO

Change Disk controller in SCO 6.0.0

So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller. First, I downloaded the megasas driver from SCO and installed it on the old system. Then I created a new Microlite Edge emergency boot cd with the new driver on it. I... (2 Replies)
Discussion started by: jgt
2 Replies

7. Solaris

Changed to AHCI, can not access disk???

Here is my problem: I have an 1.5TB disk with OpenSolaris (b134, b151a) using non AHCI. I then changed to AHCI in BIOS, which results in severe problems: I can not boot the system. I suspect the problem is because I changed to AHCI. Now I have changed back to non AHCI, but still I can not... (0 Replies)
Discussion started by: kebabbert
0 Replies

8. Solaris

Disk controller reassignment

Hi The scenario in the oracle t4-1 hardware with solaris 10 is as follows: 1. The initial install on the server was performed with an incorrect disk layout. 2. New disks were ordered and slot into the server. 3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies

9. Linux

Grub not loading from replaced disk

Hi, a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced. here is how I did that. 1) created identical partition table on the new disk. 2) attached the mirrors using md commands. The whole procedure is given below:... (2 Replies)
Discussion started by: busyboy
2 Replies

LEARN ABOUT NETBSD

icp

ICP(4)							   BSD Kernel Interfaces Manual 						    ICP(4)

NAME

     icp -- ICP-Vortex and Intel Storage RAID driver

SYNOPSIS

     icp* at pci? dev ? function ?
     ld* at icp? unit ?
     icpsp* at icp? unit ?
     scsibus* at icpsp?

DESCRIPTION

     The icp driver provides support for the newer (post 1997) ICP-Vortex GDT and Intel Storage RAID controllers.

     The ld driver provides access to logical devices (disk arrays) presented by the controller.  The icpsp driver provides direct access to other
     SCSI devices attached to the controller, such as tape or CD-ROM drives.

DIAGNOSTICS

     pci_mem_find: expected mem type 00000000, found 00000002
		   This message may be displayed during autoconfiguration if the controller's memory is mapped below 1MB in physical address
		   space.  This can be disabled either through changing a setting in the controller's BIOS utility, or changing the position of a
		   jumper on the board.  See your controller's documentation for more information.

SEE ALSO

     intro(4), ld(4), scsi(4)

HISTORY

     The icp driver first appeared in NetBSD 1.6, and was based on the FreeBSD and OpenBSD drivers of the same name.

BUGS

     ISA & EISA front-ends and a management interface are needed.

     Older PCI boards are not yet supported.

BSD
								  April 20, 2002							       BSD
All times are GMT -4. The time now is 10:59 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy