10-19-2011
Hi again, the restore of the slice layout has deleted the data, this is because the partitions have changed. Due the new / partition start now in the same block the system can start to boot but no more than this. At this point there is no more to try, except a reinstallation, so I hope that you have a correct restore data.
10 More Discussions You Might Find Interesting
1. Solaris
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies
2. Shell Programming and Scripting
In one of our internal scripts (unix.run), I have noticed that the following shebang.
#!/bin/sh -
for i in test1 test2 test3 ; do
.
.
.
Any idea what the - in the magic number stands for ?
And what impact does it have on the script ?
Continuing on the same script, I have the... (3 Replies)
Discussion started by: vino
3 Replies
3. Filesystems, Disks and Memory
I had a power outage a day ago and when the power came back on my FreeBSD 4.6 webserver had problems. It said it was unable to mount /var and made me start in single user mode and said to run fsck MANUALY. So i did and this is now what i get.
www# fsck /dev/ad0s1e
** /dev/ad0s1e
BAD SUPER... (4 Replies)
Discussion started by: matthewbane
4 Replies
4. UNIX for Advanced & Expert Users
Can any one let me know like how cn i set an label or number for each function whihc are there in an shells script:
for example
cd /opt/qcom/test/
function1()
function2()
function3()
-------
i ahe a script like this .now i want to count each of this function like 1, 2, 3,............... (3 Replies)
Discussion started by: lalitka
3 Replies
5. Solaris
/pci@if,0/pci@1,1/ide@3/dad@0,0 corrupt label wrong magic number
can u plz suggustion me (6 Replies)
Discussion started by: tirupathi
6 Replies
6. Filesystems, Disks and Memory
Whenever i run,
# fsck -F ufs /dev/dsk/c0t0d0s7
The following error prompt out:-
** /dev/dsk/c0t0d0s7
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION;
eg. fsck -o b=#
where # is the alternate super block. SEE fsck_ufs(1M).
... (3 Replies)
Discussion started by: beginningDBA
3 Replies
7. Solaris
Hello All,
I m very new to this forum.
i m having SUN NETRA X1 server with 40 GB HDD (Seagate) & 128 MB RAM.
i m trying this server for SUN 10 Practise.
As i m installing SUN 9 /10 with CD ,its giving me error after OK propmt
***************************
#boot cdrom
or
#boot cdrom... (16 Replies)
Discussion started by: amrut_k
16 Replies
8. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
9. Solaris
hi . my " /usr " was full ,so i went into the failsafe mode in solaris 10 and used format utilily to adjust space for it and labeled it. But after that whenever i try to boot solaris normally ,it is giving "magic number error"
I tried
fsck -o b=32 /dev/dsk/c0d0s6 (for /usr)
newfs -N... (6 Replies)
Discussion started by: tushardul
6 Replies
10. Solaris
This is first time post...found this forum when looking for possible solution to fix my sun pc. Just one day can't boot it already showing the following:
Boot device: disk File args:
Bad magic number in disk label
Can't open disk label package
Evaluating: boot
Can't open boot device... (40 Replies)
Discussion started by: SHuKoSuGi
40 Replies
WREN(3) Library Functions Manual WREN(3)
NAME
wren, ata - hard disk interface
SYNOPSIS
bind #H[drive] /dev
bind #w[target[.lun]] /dev
/dev/hd0disk
/dev/hd0partition
/dev/sd0disk
/dev/sd0partition
...
DESCRIPTION
The hard disk interfaces (wren, #w, is a SCSI disk; ata, #H, is an IDE or ATA disk) serve a one-level directory giving access to the hard
disk partitions. The parameter to attach defines the numerical SCSI target and logical unit number or the IDE drive number to access.
Both default to zero.
Each partition name is prefixed by hd and the numeric drive identifier. The partition always exists and covers the entire disk. The size
of each partition as reported by stat(2) is the number of bytes in the partition, so the size of is the size of the entire disk.
The partition also always exists; it is the last block on the disk for SCSI, second to last for IDE. If it contains valid partition data,
those partitions will be visible as well. Every time the device is bound, the partitions are updated to reflect any changes in the parti-
tion file.
The format of the partition file is the string
plan9 partitions
on a line, followed by partition specifications, one per line, consisting of a name and textual strings for the block start and limit for
each partition on the disk.
The program prep(8) writes the partition table for the disk; its use is preferred to writing it by hand.
SEE ALSO
prep(8), scsi(3)
SOURCE
/sys/src/9/port/devwren.c
/sys/src/9/pc/devata.c
WREN(3)