|
|
Sponsored Content
Operating Systems
Linux
(ASK) Question about linux network...
Post 302562431 by busoh.sensen on Thursday 6th of October 2011 10:34:20 PM
10-06-2011
thanx Hartz, sorry for late reply...
I've tried the last | grep 192.xxxxx
but the result was nothing.
and ifconfig -a to look just for local IP, not all existing IP on my network? like 192.168.1.1; 192.168.1.2; 192.168.1.3.....etc
cmiiw
the problem is, I have a server that its name xxx.lan (example), and I usually access from Windows
start-run \ \ xxx, and now... forget what its IP
now, can i know the IP xxx, and anyone who access that server? and also the Log?
many thnx
I've tried the last | grep 192.xxxxx
but the result was nothing.
and ifconfig -a to look just for local IP, not all existing IP on my network? like 192.168.1.1; 192.168.1.2; 192.168.1.3.....etc
cmiiw
the problem is, I have a server that its name xxx.lan (example), and I usually access from Windows
start-run \ \ xxx, and now... forget what its IP
now, can i know the IP xxx, and anyone who access that server? and also the Log?
many thnx
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hey,
Just need a little help I'm not sure wat I should do.
We have several little networks setup for testing different things. One of these networks we need to have running at full dulpex.
Right now we run 2 hubs (to go off to 2 differnt parts) and they are half dulpex hubs.
Is is... (1 Reply)
Discussion started by: merlin
1 Replies
2. Linux
I have setup a AS 2.1 server with no X running or installed. I need to know how to configure the IP and such from command line and change it from DHCP. We used DHCP at first since we didn't know the IP we were going to use and now I need to change it. Any help would be great as Redhat's site just... (2 Replies)
Discussion started by: Acleoma
2 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. UNIX for Dummies Questions & Answers
This is my first attempt in installing a netbsd ever. I'm trying to get myself familiar with some commands and how things work in unix and so far i never knew its this fun. Anyway, unix is our elective here in school and school is gonna start 2 weeks. I'm just trying to get a headstart on this :D... (2 Replies)
Discussion started by: 3rr0r_3rr0r
2 Replies
5. UNIX for Dummies Questions & Answers
1) how do i know my NIC speed if its 10//100???
2)how do i setup by NIC to full duplex
3) any help on setting up etherchannel for NIC failover (1 Reply)
Discussion started by: karthikosu
1 Replies
6. Solaris
I am new to Solaris and have been searching around for this answer and I think I figured it out but I wanted to run it by you folks. I was trying to figure out if the network on this Solaris 10 machine was set up for 100 Full Duplex. I think from this output that it is 100 full duplex, am I... (2 Replies)
Discussion started by: scotbuff
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ? :confused: (2 Replies)
Discussion started by: mik
2 Replies
8. IP Networking
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
Discussion started by: scofiled83
2 Replies
9. IP Networking
Folks;
I have 2 SUSE servers similar in all configuration & both on the same network
(192.168.151.10 & 192.168.151.11) with the same default gateway of 192.168.151.1 and the same netmask of 255.255.255.0 and the same firewall configuration
the first one works fine and i can ssh to it & i can... (3 Replies)
Discussion started by: Katkota
3 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I am on Redhat 5. on the /etc/sysconfig/network file
I don't see GATEWAY as one line. I also checked /etc/sysconfig/network-scripts/ifcfg-eth0. I don't see GATEWAY.
But on the server. But when I do netstat -rn. I see many address. Is there some other settings ?
... (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8) NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h] DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows: iqn.2001-04.com.<hostname>-<target_name> The target name must be unique. The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia- tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator. EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81: tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82: tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82 Create a target that uses /dev/sdb1 and allows connections from any initiator: tgt-setup-lun -d /dev/sdb1 -n my_target Display help: tgt-setup-lun -h AUTHOR
Written by Erez Zilber REPORTING BUGS
Report bugs to <erezz@voltaire.com>. COPYRIGHT
Copyright (C) Voltaire Ltd. 2008. tgt-setup-lun(8)