to configure ip address Post: 302561601

10 More Discussions You Might Find Interesting

1. IP Networking

trying to configure DNS address in Solaris

hi to all. I'm trying to use the sendmail command to generate some reports and I cant use it. The mails i try to send simply won't go out, instead I receive a response from the system sayng that the host is unknown. I think the problem is in the DNS configuration (or the IMAP/SMTP servers). ...

2. UNIX for Dummies Questions & Answers

network address and broadcast address?

say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on? And could you explain how to get the answer? thanx in advance!

3. IP Networking

How to Achive IP address through MAC(Ethernet) address

Hi sir, i want to make such programe which takes MAC(Ethernet) address of any host & give me its IP address....... but i'm nt getting that how i can pass the MAC address to Frame........ Please give me an idea for making such program... Thanks & regards Krishna

4. UNIX for Dummies Questions & Answers

Panic kernal-mode address fault on user address 0x14

:) Firstly Hi all!!, im NEW!! and on here hoping that someone might be able to offer me some help... i have a server that keeps crashing every few days with the error message: PANIC KERNAL-MODE ADDRESS FAULT ON USER ADDRESS 0X14 KERNAL PAGE FAULT FROM (CS:EIP)=(100:EF71B5BD) EAX=EF822000...

5. Solaris

How to Configure a Static Ip Address

Hello friend, I am new in UNIX, but I want to learn a lot Well I have a problem to try to configure my PC with a static IP Address (IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1) (DNS 200.48.225.130 and 200.48.225.146). where are the file that I must be change? The SO is Sun Solaris...

6. IP Networking

Tracing a MAC address to IP address: Solaris

Hi there I lost connectivity to one of our remote systems and when I checked the messages log I found the following: Aug 10 23:42:34 host xntpd: time reset (step) 1.681729 s Aug 16 13:20:51 host ip: WARNING: node "mac address" is using our IP address x.x.x.x on aggr1 Aug 16 13:20:51 host...

7. Cybersecurity

Configure iptables to allows list of MAC address

Hi all, I want to make this nw diagram: Small NW ---(eth1)-- Linux iptables --(eth0)---LAN NW And with these requirements: 1. Allow only 1 Mac address aa-aa-aa-aa-aa-aa from Small NW to LAN NW 2. Allow list of Mac addresses from LAN NW access to Small NW What will I...

8. Shell Programming and Scripting

configure from address in mailx command

Hi, I need to configure customized from address in mailx command. Can you pls tell me the option for configuring from address. Thanks Latika

9. IP Networking

Configure squid to listen on any IP address with port 80

Hi, I am trying to configure a transparent squid cache. When I try to use the below option in squid.conf, squid listens on port 80 only for the IP address configured on the system's interface. http_port 80 transparent But I want squid to accept connections for any IP address on port 80....

10. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program

LEARN ABOUT MINIX

ifconfig

IFCONFIG(8)						      System Manager's Manual						       IFCONFIG(8)

NAME

       ifconfig - configure a TCP/IP device

SYNOPSIS

       ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv]

DESCRIPTION

       Ifconfig  initializes a TCP/IP device setting the IP address and/or netmask.  It will report the address and netmask set.  This command may
       be used if the system has not been configured properly yet.  It is only used at boot time to set a fixed address for  a	system	without  a
       physical ethernet.  Normally the inet task will find it out by itself from the RARP server.

OPTIONS

       -h     The decimal TCP/IP address to set.

       -n     The netmask to set.

       -i     Don't set the IP address or netmask if already set.  This way ifconfig cannot interfere if the numbers have been found out by RARP.

       -v     Report IP address and netmask.  This is the default action if there are no other options.

SEE ALSO

       hostaddr(1), rarpd(8), set_net_default(8), boot(8).

AUTHOR

       Kees J. Bot (kjb@cs.vu.nl)

																       IFCONFIG(8)

10 More Discussions You Might Find Interesting

1. IP Networking

trying to configure DNS address in Solaris

Discussion started by: ldrojasm

2. UNIX for Dummies Questions & Answers

network address and broadcast address?

Discussion started by: pnxi

3. IP Networking

How to Achive IP address through MAC(Ethernet) address

Discussion started by: krishnacins

4. UNIX for Dummies Questions & Answers

Panic kernal-mode address fault on user address 0x14

Discussion started by: Twix