09-14-2011
scroll to the bottom of this page and follow the links!
9 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. Solaris
Hi..i have installed solaris 10 on vmware. I m not able connect to internet.
pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies
3. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
4. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
5. Solaris
Hi gurus
Could anybody tell me that what are the kernal parameter of network interface in solaris
Regards (3 Replies)
Discussion started by: girish.batra
3 Replies
6. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
7. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
8. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
9. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
SLATTACH(8) System Manager's Manual SLATTACH(8)
NAME
slattach - attach serial lines as network interfaces
SYOPNSIS
slattach ttyname [ baudrate ]
DESCRIPTION
Slattach is used to assign a tty line to a network interface, and to define the network source and destination addresses. The ttyname
parameter is a string of the form ``ttyXX'', or ``/dev/ttyXX''. The optional baudrate parameter is used to set the speed of the connec-
tion. If not specified, the default of 9600 is used.
Only the super-user may attach a network interface.
To detach the interface, use `ifconfig interface-name down' after killing off the slattach process. interface-name is the name that is
shown by netstat(1)
EXAMPLES
slattach ttyh8
slattach /dev/tty01 4800
DIAGNOSTICS
Messages indicating the specified interface does not exit, the requested address is unknown, the user is not privileged and tried to alter
an interface's configuration.
SEE ALSO
rc(8), intro(4), netstat(1), ifconfig(8)
4.3 Berkeley Distribution November 17, 1996 SLATTACH(8)