09-06-2011
Put your server name (idm187-05) into /etc/hosts... so when you do your ypinit, the names you specify there resolve.
9 More Discussions You Might Find Interesting
1. Solaris
hello,
after couple days trying to configure SMC to work with NIS on Solaris 8, i gave up...have any of you have done it before? what change did you make when you edited the toolbox? also, when you create a new toolbox, they ask for server and domain, what do you have to fill into these two... (0 Replies)
Discussion started by: hlude92
0 Replies
2. UNIX for Advanced & Expert Users
Our NIS master server went down. We have since fixed it and brought it back up. However all of are machines still point to the slave server when looking at it with ypwhich. My question is how do i point the servers back to the master.
Frank (2 Replies)
Discussion started by: frankkahle
2 Replies
3. UNIX for Advanced & Expert Users
I am running a DNS/NIS server on and older 2.6 system. I would like to move it to a newer system running Sol9. I have not found a good HOWTO and was looking for some advice.
Thanks in advance.
Dave (4 Replies)
Discussion started by: dlalonde
4 Replies
4. Solaris
Hi All,
I get below error while running
cd /var/yp
/usr/sbin/ypinit -m
Error Code - 1
updated netmasks
make : warning : target all not remade because of errors
current working dir /var/yp
*** error code 1 ***
make : fatal error : command failed for target 'k'
error running... (4 Replies)
Discussion started by: naw_deepak
4 Replies
5. Solaris
Hello All,
I just tried to create NIS master in my x86 vmware machine. I have followed the steps and created the necessary files and installed via ypinit command. Now the issue is after start the services when provide the ypwhich command showing following error. Please assist.
bash-#svcs... (1 Reply)
Discussion started by: gowthamakanthan
1 Replies
6. HP-UX
I have a NIS Master server and NIS Clients.
But when I started the service all the process and files that should be owne by root apper by the owner 0
This is an example
0 1709 1708 0 10:06:10 ? 0:00 /usr/sbin/nfsd 4
0 1710 1709 0 10:06:10 ? 0:00 /usr/sbin/nfsd 4
0 1708 1 0 10:06:10 ? 0:00... (2 Replies)
Discussion started by: GCSG
2 Replies
7. Red Hat
Goodmorning
i am preparing Nis for my test lab.Running Redhat 5.4 on master and centos for my client.Master server running portmap,ypserv,yppasswdd and client running portmap,ypbind and ypxfrd.
ypcat and other yp commands are running fine frm client.But when i try yppasswdd on client to change... (1 Reply)
Discussion started by: Vaibhav.T
1 Replies
8. UNIX Desktop Questions & Answers
I have an application desigend in PHP and MySQl running on apache web server that I is running on a Amazon EC2 server Centos. I want to implement the master-master and master slave replication and high availability disaster recovery on this application database.
For this I have created two... (0 Replies)
Discussion started by: Palak Sharma
0 Replies
9. UNIX for Advanced & Expert Users
I have some scripts where I go and do some LDAP/NIS queries to report on users on Unix servers. What I am trying to figure out is, how do I know which server is the LDAP? The configs have been in place long before I took over so was hoping someone had some insight on how to figure this out. I must... (1 Reply)
Discussion started by: dagamier
1 Replies
ypinit(1M) System Administration Commands ypinit(1M)
NAME
ypinit - set up NIS client
SYNOPSIS
/usr/sbin/ypinit [-c] [-m] [-s master_server]
DESCRIPTION
ypinit can be used to set up an NIS client system. You must be the superuser to run this command. This script need not be used at all if
ypbind(1M) is started with the -broadcast option (it is invoked with this option from the svc:/network/nis/client:default service).
Normally, ypinit is run only once after installing the system. It may be run whenever a new NIS server is added to the network or an
existing one is decommissioned.
ypinit prompts for a list of NIS servers to bind the client to; this list should be ordered from the closest to the furthest server. Each
of these NIS servers must be listed in either the /etc/hosts or the /etc/inet/ipnodes file along with its IP address. ypinit stores the
list in file /var/yp/binding/domain/ypservers. This file is used by ypbind when run without the -broadcast option.
OPTIONS
-c Set up a ypclient system.
-m Build a master ypserver data base.
-s master_server Slave data base. master_server must be the same master configured in the YP maps and returned by the ypwhich -m
command.
FILES
/etc/hosts
/etc/inet/ipnodes
/var/yp/binding/domain/ypservers
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWnisu |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), svcadm(1M), ypbind(1M), sysinfo(2), hosts(4), ipnodes(4), attributes(5), smf(5)
NOTES
The NIS client service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/nis/client:default
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
BUGS
ypinit sets up the list of NIS servers only for the current domain on the system when it is run, that is, the domain returned by the
SI_SRPC_DOMAIN command to sysinfo(2). Care should be taken to ensure that this is the same as the desired domain for NIS client processes.
SunOS 5.10 13 Aug 2004 ypinit(1M)