|
|
Sponsored Content
Operating Systems
AIX
Multipathing in AIX
Post 302549770 by csorhand on Wednesday 24th of August 2011 01:39:02 AM
08-24-2011
|
|
10 More Discussions You Might Find Interesting
1. Solaris
We have loads of Sparc solaris 8 boxes. Each one has 2 physical interfaces and 2 virtuals set up for multipathing (See ifconfig below). Problem is that I cannot ping the qfe0 interface IP from the local machine. I can ping all other local interfaces, but not 10.161.19.5. I can ping it from... (3 Replies)
Discussion started by: tjlst15
3 Replies
2. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
3. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
4. IP Networking
Hii Every One,
I am working on SUN server installed with Solaris-10,
1) I want to assign a vertual IP to a interface (ce1).
2) And with that vertual IP and one more interface (ce2), I want to do IP
multipathing.
So, kindely help me to achive above tasks by discribing... (2 Replies)
Discussion started by: prashantshukla
2 Replies
5. Solaris
Hi,
Basically the original configuration on my Solaris 9 server was two LUNs configured as Veritas file systems that were connected to a NetApp filer (filer1). These two LUNs are still configured on the server - but are not being used. They are there as a backup just in case the new... (0 Replies)
Discussion started by: sparcman
0 Replies
6. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
7. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
8. Red Hat
I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist.
# multipath -l
mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX
\_ round-robin 0
\_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies
9. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
10. UNIX for Advanced & Expert Users
I have a bit of an odd situation I would like to float out here and see if anyone has any ideas on this..
We are working on doing Disaster Recovery on a number of RHEL 7.4 systems. These are running on Cisco Blade Servers.
The mount point for /boot is on a Multipathed SAN LUN. There are a... (4 Replies)
Discussion started by: Overcast451
4 Replies
LEARN ABOUT CENTOS
install-solaris
install-solaris(1M) install-solaris(1M) NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)