08-23-2011
rs232 pinout - Google Search
You only need to connect three wires, pin 2 (red) , 3(green) and 7(black) on the 25 pin end.
On the 9 pin end connect pins 2(red),3(green), and 5(black).
Set the terminal to use xon-xoff flow control.
This User Gave Thanks to jgt For This Post:
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
2. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
3. UNIX for Dummies Questions & Answers
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies
4. Solaris
HI all,
i still have a problem when using null modem to see the output from my server(sun ultra en 3000).
i followed the instruction from the internet, but it is not working.
1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port).
2.... (3 Replies)
Discussion started by: waterbear
3 Replies
5. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
6. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
7. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
8. AIX
Current setup:
Some old AIX standalone machine (F series)
My WinXP laptop
Null modem cable from laptop to AIX machine (console port).
On Hypterminal on WinXP I can connect to the AIX machine (serial connection), but when I try to transfer file, it will just sit there. I'm guessing the... (3 Replies)
Discussion started by: apra143
3 Replies
9. AIX
I configured the serial modem in my P6-550 AIX 5.3 box
But i dont have telephone line.
when I run the command
# cu -l /dev/tty1
the output is as follows
does it mean that my modem is responding to the command?
can i say my serial port is working and communicating fine?
Connected
... (3 Replies)
Discussion started by: pchangba
3 Replies
CZ(4) BSD Kernel Interfaces Manual CZ(4)
NAME
cz -- Cyclades-Z series multi-port serial adapter device driver
SYNOPSIS
cz* at pci? dev ? function ?
DESCRIPTION
The cz device driver supports the Cyclades-Z series of multi-port serial adapters. The Cyclades-Z is an intelligent serial controller com-
prising:
o PLX9060ES PCI bus interface
o Xilinx XC5204 FPGA
o IDT R3052 MIPS CPU
The MIPS CPU runs firmware provided by the device driver. Communication with the MIPS is performed by modifying data structures located in
board local RAM or host RAM.
The Cyclades-Z comes in three basic flavors:
o Cyclades-8Zo rev. 1 -- This is an older 8-port board with no FPGA. The serial ports are provided by an octopus cable.
o Cyclades-8Zo rev. 2 -- This is the newer 8-port board. The serial ports are provided by an octopus cable.
o Cyclades-Ze -- This is the expandable version of the Cyclades-Z. It uses an HD-50 SCSI cable to connect the board to a 1U rack
mountable serial expansion box. Each box has 16 RJ45 serial ports, and up to 4 boxes may be chained together, for a total of 64
ports. Boxes 3 and 4 require their own external power supply, otherwise the firmware will refuse to start (as it cannot communi-
cate with the UARTs in those boxes).
The Cyclades-Z has several features to improve performance under high serial I/O load:
o The board may operate in interrupt-driven mode or polled mode to reduce interrupt load.
o Each channel has a large input and output buffer.
o Each channel may be programmed to generate an interrupt based on reception of a specific character, e.g. a PPP End-Of-Frame charac-
ter.
o The MIPS CPU on the board performs all flow-control handling.
FILES
/dev/ttyCZnnnn -- dial-in (normal) TTY device
/dev/dtyCZnnnn -- dial-out TTY device
SEE ALSO
pci(4), termios(4), tty(4)
HISTORY
The cz driver first appeared in NetBSD 1.5.
AUTHORS
The cz driver was written by Jason R. Thorpe <thorpej@zembu.com> and
Bill Studenmund <wrstuden@zembu.com> of Zembu Labs, Inc.
BUGS
The cz driver does not currently implement communication via host RAM. While this may improve performance by reducing the number of PCI mem-
ory space read/write cycles, it is not straightforward to implement with the current bus_dma(9) API.
Interrupt mode has not been tested.
There is no support for reading or writing the EEPROM connected to the PLX PCI bus controller.
BSD
May 17, 2000 BSD