08-04-2011
10 More Discussions You Might Find Interesting
1. Solaris
We have loads of Sparc solaris 8 boxes. Each one has 2 physical interfaces and 2 virtuals set up for multipathing (See ifconfig below). Problem is that I cannot ping the qfe0 interface IP from the local machine. I can ping all other local interfaces, but not 10.161.19.5. I can ping it from... (3 Replies)
Discussion started by: tjlst15
3 Replies
2. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
3. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
4. IP Networking
Hii Every One,
I am working on SUN server installed with Solaris-10,
1) I want to assign a vertual IP to a interface (ce1).
2) And with that vertual IP and one more interface (ce2), I want to do IP
multipathing.
So, kindely help me to achive above tasks by discribing... (2 Replies)
Discussion started by: prashantshukla
2 Replies
5. Solaris
Hi,
Basically the original configuration on my Solaris 9 server was two LUNs configured as Veritas file systems that were connected to a NetApp filer (filer1). These two LUNs are still configured on the server - but are not being used. They are there as a backup just in case the new... (0 Replies)
Discussion started by: sparcman
0 Replies
6. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
7. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
8. Red Hat
I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist.
# multipath -l
mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX
\_ round-robin 0
\_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies
9. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
10. UNIX for Advanced & Expert Users
I have a bit of an odd situation I would like to float out here and see if anyone has any ideas on this..
We are working on doing Disaster Recovery on a number of RHEL 7.4 systems. These are running on Cisco Blade Servers.
The mount point for /boot is on a Multipathed SAN LUN. There are a... (4 Replies)
Discussion started by: Overcast451
4 Replies
IRSEND(1) FSF IRSEND(1)
NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)