08-04-2011
10 More Discussions You Might Find Interesting
1. Solaris
We have loads of Sparc solaris 8 boxes. Each one has 2 physical interfaces and 2 virtuals set up for multipathing (See ifconfig below). Problem is that I cannot ping the qfe0 interface IP from the local machine. I can ping all other local interfaces, but not 10.161.19.5. I can ping it from... (3 Replies)
Discussion started by: tjlst15
3 Replies
2. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
3. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
4. IP Networking
Hii Every One,
I am working on SUN server installed with Solaris-10,
1) I want to assign a vertual IP to a interface (ce1).
2) And with that vertual IP and one more interface (ce2), I want to do IP
multipathing.
So, kindely help me to achive above tasks by discribing... (2 Replies)
Discussion started by: prashantshukla
2 Replies
5. Solaris
Hi,
Basically the original configuration on my Solaris 9 server was two LUNs configured as Veritas file systems that were connected to a NetApp filer (filer1). These two LUNs are still configured on the server - but are not being used. They are there as a backup just in case the new... (0 Replies)
Discussion started by: sparcman
0 Replies
6. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
7. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
8. Red Hat
I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist.
# multipath -l
mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX
\_ round-robin 0
\_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies
9. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
10. UNIX for Advanced & Expert Users
I have a bit of an odd situation I would like to float out here and see if anyone has any ideas on this..
We are working on doing Disaster Recovery on a number of RHEL 7.4 systems. These are running on Cisco Blade Servers.
The mount point for /boot is on a Multipathed SAN LUN. There are a... (4 Replies)
Discussion started by: Overcast451
4 Replies
LEARN ABOUT DEBIAN
locale::script
Locale::Script(3perl) Perl Programmers Reference Guide Locale::Script(3perl)
NAME
Locale::Script - standard codes for script identification
SYNOPSIS
use Locale::Script;
$script = code2script('phnx'); # 'Phoenician'
$code = script2code('Phoenician'); # 'Phnx'
$code = script2code('Phoenician',
LOCALE_CODE_NUMERIC); # 115
@codes = all_script_codes();
@scripts = all_script_names();
DESCRIPTION
The "Locale::Script" module provides access to standards codes used for identifying scripts, such as those defined in ISO 15924.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 15924
four-letter codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying scripts. The ones currently supported are:
alpha
This is a set of four-letter (capitalized) codes from ISO 15924 such as 'Phnx' for Phoenician.
This code set is identified with the symbol "LOCALE_SCRIPT_ALPHA".
The Zxxx, Zyyy, and Zzzz codes are not used.
This is the default code set.
numeric
This is a set of three-digit numeric codes from ISO 15924 such as 115 for Phoenician.
This code set is identified with the symbol "LOCALE_SCRIPT_NUMERIC".
ROUTINES
code2script ( CODE [,CODESET] )
script2code ( NAME [,CODESET] )
script_code2code ( CODE ,CODESET ,CODESET2 )
all_script_codes ( [CODESET] )
all_script_names ( [CODESET] )
Locale::Script::rename_script ( CODE ,NEW_NAME [,CODESET] )
Locale::Script::add_script ( CODE ,NAME [,CODESET] )
Locale::Script::delete_script ( CODE [,CODESET] )
Locale::Script::add_script_alias ( NAME ,NEW_NAME )
Locale::Script::delete_script_alias ( NAME )
Locale::Script::rename_script_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Script::add_script_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Script::delete_script_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes man page.
SEE ALSO
Locale::Codes
Locale::Constants
http://www.unicode.org/iso15924/
Home page for ISO 15924.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 1997-2001 Canon Research Centre Europe (CRE).
Copyright (c) 2001-2010 Neil Bowers
Copyright (c) 2010-2011 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.14.2 2011-09-26 Locale::Script(3perl)