your card may not be recognized by the OS. you might need to install a driver for that card or it might be unplumbed.
if it doesn't show anything, you need to install a driver for your card. check on windows what type of card you have or in Solaris:
look for your card on the list. and search the net for the driver.
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi all,
I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help?
Thanks,
Neked (1 Reply)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
hi,
i have sunfire 280r sparc. i would like to know how to setup interface with command ndd line and put it in the file permanently.
my card is eri0 and speed can be 100mb or 1000mb full duplex.
thanks in advance. (3 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT MOJAVE
suninstall
suninstall(1M) System Administration Commands suninstall(1M)NAME
suninstall - install the Solaris operating system
SYNOPSIS
suninstall
DESCRIPTION install-solaris(1M) is now the preferred command for starting and restarting the Solaris Installation program. It should be used instead of
suninstall. suninstall is symbolically linked to install-solaris.
suninstall is a forms-based and graphical subsystem for installing the operating system.
suninstall exists only on the Solaris installation media (CD or DVD) and should only be invoked from there. Refer to the Solaris 10 Instal-
lation Guide: Basic Installations for more details.
suninstall allows installation of the operating system onto any standalone system. suninstall loads the software available on the installa-
tion media. Refer to the Solaris 10 Installation Guide: Basic Installations for disk space requirements.
USAGE
Refer to the Solaris 10 Installation Guide: Basic Installations for more information on the various menus and selections.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
SEE ALSO pkginfo(1), install(1M), install-solaris(1M), pkgadd(1M), attributes(5)
Solaris 10 Installation Guide: Basic Installations
NOTES
It is advisable to exit suninstall by means of the exit options in the suninstall menus.
SunOS 5.10 9 Sep 2004 suninstall(1M)