07-19-2011
jlliagre,
Thanks for the info. I will have to look into exclusive IP zones. Can you tell me the disadvantages of the way I do it. This way I can learn from you.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
4. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT OPENDARWIN
zprint
ZPRINT(1) General Commands Manual ZPRINT(1)
NAME
zprint - show information about kernel zones
SYNOPSIS
zprint [-w] [-s] [-c] [-h] [name]
DESCRIPTION
zprint(1) displays data about Mach zones. By default, zprint will print out information about all Mach zones. If the optional name is
specified, zprint will print information about each zone for which name is a substring of the zone's name.
zprint interprets the following options:
-w For each zone, zprint calculates how much space is allocated but not currently in use, the space wasted by the zone.
-s zprint sorts the zones, showing the wasting the most memory first.
-c (Default) zprint prints zone info in columns. Long zone names are truncated with '$', and spaces are replaced with '.', to allow
for sorting by column. Pageable and collectible zones are shown with 'P' and 'C' on the far right. Zones with preposterously large
maximum sizes are shown with '----' in the max size and max num elts fields.
-h (Default) Shows headings for the columns printed with the -c option. It may be useful to override this option when sorting by col-
umn.
Any option (including default options) can be overridden by specifying the option in upper-case; for example, -C overrides the (default)
option -c.
SEE ALSO
host_zone_info(2).
27/02/87 ZPRINT(1)