07-19-2011
@bitlord, this method has many disadvantages. It was useful before exclusive IP zones were introduced but has now lost most of its interest.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
4. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT OPENSOLARIS
tzmon
tzmon(7d) Devices tzmon(7d)
NAME
tzmon - ACPI Thermal Zone Monitor
DESCRIPTION
The tzmon is a pseudo driver that serves as an ACPI thermal zone monitor. Thermal zones are logical regions within a computer system for
which ACPI performs temperature monitoring and control functions. The number of thermal zones on a system with ACPI support varies. For
example, some systems may have one or more thermal zones, while others may have none. See the Advanced Configuration and Power Interface
Specification, (ACPI) Version 3.0A. for more details.
The tzmon handles thermal Zone events from ACPI and polls the temperature for each zone exposed by the ACPI implementation. If threshold
temperatures are reached, tzmon takes appropriate action. For example, if the temperature is sufficiently high and the ACPI implementation
supports it, tzmon initiates system shutdown.
Note that by default, system temperature control functions are usually performed by the BIOS and may supersede tzmon functions, depending
on the BIOS implementation. Also, many ACPI implementations expose no thermal zones and in these cases, tzmon performs no functions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWckr |
+-----------------------------+-----------------------------+
|Architecture |x86/x64 only |
+-----------------------------+-----------------------------+
|Interface stability |Private |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
Advanced Configuration and Power Interface Specification, (ACPI), Version 3.0A.
SunOS 5.11 31 Oct 2006 tzmon(7d)