Help with tape drive Post: 302539166

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Tape drive install

I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default? help..

2. Linux

Installing tape drive?

Hello. I have Redhat 8.0 on a laptop. Working good. I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already...

3. UNIX for Dummies Questions & Answers

tape drive

Hi, I need to restore my tape backup, when I type "tape status" it gives; status : ready beginning-of-tape write-protected soft errors : 0 hard errors : 0 underruns : 3 but...

4. AIX

Tape Drive

I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How...

5. SCO

Tape Drive Configuration

Dear All, I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as...

6. SCO

Tape Drive Logs?

I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out. I have run HP diagnostics on the array,...

7. UNIX for Dummies Questions & Answers

Quantum tape drive

Hi, Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected? I used to work on Solaris, I used to do...

8. HP-UX

TAPE drive

I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help? Thanks in advance

LEARN ABOUT CENTOS

tapset::scsi

tapset::scsi(3stap)													       tapset::scsi(3stap)

NAME

       tapset::scsi - systemtap scsi tapset

DESCRIPTION

	This family of probe points is used to probe SCSI activities.

       scsi.ioentry
	      Prepares a SCSI mid-layer request

	       See probe::scsi.ioentry(3stap)
	       for details.

       scsi.iodispatching
	      SCSI mid-layer dispatched low-level SCSI command

	       See probe::scsi.iodispatching(3stap)
	       for details.

       scsi.iodone
	      SCSI command completed by low level driver and enqueued into the done queue.

	       See probe::scsi.iodone(3stap)
	       for details.

       scsi.iocompleted
	      SCSI mid-layer running the completion processing for block device I/O requests

	       See probe::scsi.iocompleted(3stap)
	       for details.

       scsi.ioexecute
	      Create mid-layer SCSI request and wait for the result

	       See probe::scsi.ioexecute(3stap)
	       for details.

       scsi.set_state
	      Order SCSI device state change

	       See probe::scsi.set_state(3stap)
	       for details.

SEE ALSO

	  probe::scsi.ioentry(3stap),	   probe::scsi.iodispatching(3stap),	  probe::scsi.iodone(3stap),	 probe::scsi.iocompleted(3stap),
       probe::scsi.ioexecute(3stap),  probe::scsi.set_state(3stap),  stap(1), stapprobes(3stap)

IBM
									---						       tapset::scsi(3stap)