06-17-2011
Requirment are without password to get hardware info in the the linux using Qt?
Dear All,
I have developed one application in the Qt Creator. I have one requirment for get hardward information in the Linux system, Then i try dmidecode using and run in Qt.It will occur error message for "dev/mem" permission denied". So i try to terminal to run sudo ./application. it will ask password after enter the password the application running and get hardwareinfo also. So how to do in Qt. Please help me it urgent.
requirment are without password to get hardware info in the the linux using Qt?
Thanks..
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
is there a command to find out processor speed, RAM size, ets?
i need it for Solaris 5.6, 5.7 and linux (4 Replies)
Discussion started by: sillY
4 Replies
2. UNIX for Dummies Questions & Answers
Hi
I am a new comer for Unix sys. My Unix experience just less than half a year. Now Im going to purchase a notebook to install Unix system, but I have no idea of the mini setting for the laptop that are able to run Unix fluently. Is that anyone can tell me? Please give more options or... (1 Reply)
Discussion started by: Julius
1 Replies
3. Linux
I'm really new to this and I want to learn UNIX/LINUX and saw the post about setting up a server to use everyday to practice. I have an old 386 PC and a 486 PC sitting around. Can they be reformatted and used to run UNIX/LINUX on as a network. (4 Replies)
Discussion started by: Barkingmad
4 Replies
4. UNIX for Dummies Questions & Answers
I would like to configure a bare minimum Linux with internet browser on a system with Flash & RAM (but no harddisk or any other nonvolatile storage). Please advise. (5 Replies)
Discussion started by: rherb
5 Replies
5. Solaris
Hello,
I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as:
HBA Model Name
HBA Firmware version
HBA Port details
HBA Driver details
First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
Discussion started by: flagman5
6 Replies
6. UNIX for Dummies Questions & Answers
We have run software on Dell Servers w/ Windows and seen the performance degrade overtime. We switched to an IBM server w/ AIX and have not seen the same performance degradation over time. In fact, the IBM servers are at least five years old and continue to preform well at the same level.
How... (2 Replies)
Discussion started by: bggibson
2 Replies
7. AIX
Hello all. I'm new to AIX and IBM hardware and I have a question around the configuration of the service processor on the power series. I need to know:
1) How do I get into the service processor from the serial console when AIX is up and running. I come from the Sun world and I tried all I know.... (1 Reply)
Discussion started by: glenc2004
1 Replies
8. Hardware
Hello folks,
I pretend acquire this hardware:
1-Motherboard Asus Skt1151 - H110M-A/M.2 (https://www.asus.com/pt/Motherboards...cifications/);
2-Intel i5 6400 2.7Ghz QuadCore Skt1151;
or
2-Intel i5 6500 3.2Ghz QuadCore Skt1151;
3-Dimm 8GB DDR4 Kingston CL15 2133Mhz;
Obvious I pretend... (1 Reply)
Discussion started by: enodev
1 Replies
LEARN ABOUT OSF1
yppasswd
yppasswd(1) General Commands Manual yppasswd(1)
NAME
yppasswd - change password in Network Information Service (NIS)
SYNOPSIS
yppasswd [name]
DESCRIPTION
Note
If Enhanced Security is enabled on your system, use the passwd command to change your password, even if NIS is in use.
The yppasswd command lets you change your password in the Network Information Service (NIS) map, a network data base service. Only you or
the superuser can change your NIS password.
When you enter the yppasswd command, the program prompts you for the old password and then for the new password. Note that the passwords
are not displayed on the screen.
Next, the program asks you for the new password again, to verify that you have typed it correctly. If you do not type the passwords cor-
rectly, you will receive an error message after you enter the new password.
Your new NIS password must meet one of the following requirements: It must be a combination of at least six alphanumeric characters, or It
must be a minimum of four characters, with at least one being non-alphanumeric, such as a control sequence.
Note
The passwd command does not change the NIS password. This command only changes the local password file (/etc/passwd), and not the NIS mas-
ter password file.
ERRORS
Your new password does not meet the minimum length requirement. You misspelled your new password or its verification. Your new password
can not be activated. It must be different from your old password and your login name.
FILES
Password file NIS directory
SEE ALSO
passwd(1), passwd(4), ypfiles(4), yppasswdd(8)
Network Administration
yppasswd(1)