Appologies, I ment Ubuntu 10.04, still bit of a noob here
I retried to recompile, after clean, mrporper, olconfig I did a new menuconfig. Now I think I enable as much as possible and set the proccesor family up better (maybe this will do anything good), but it's still quite confusing where to look as I have hardly any idea what those conigurations mean. After a lot of hassle I solved the ipipe_o error, but now it goes on about this;
I know If I disable Xenomai altogether it should compile, but I think that got me in a mess earlier. Could you please advise on proper config settings?
Thanks.
Hi,
I've just bought an Ultra 60 running solaris 9 (or so I've been led to believe). When I start up, it looks for a (presumably) domain/network to hook up to and the following messages are displayed:
Boot device: net file and args:
Network link setup failed
Please check cable and try... (3 Replies)
Hi all ,
i was trying to upgrade firmware on machine 7028-6E4 and it failed .
Now machine does not boot anymore , i can not get SMC menu either ...
What are my options ?
Thanks,
Rahim (1 Reply)
I'm running solaris 2.5.1. My main development server is DEAD, i can't even boot off the cdrom, it powers up, acts like it is starting the boot process but then says cannot find boot device. I've done the search here on this site and saw the other posts, but at the ok prompt it won't even let me... (3 Replies)
Solaris system
version 6
I cloned the drive using the DD command.
Using the format command and examining the partitions, all looks the same as the original drive.
Problem:
When I attach the cloned drive as the master, and only drive in system, it will not boot.
Error messages:
... (9 Replies)
I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the... (0 Replies)
I'm trying to install Fedora 9 on a Dell OptiPlex GX300 machine. The instalation runs properly, but when the computer restarts after the instalation, it simply won't boot, like there's no OS installed.
I tried diffrent Linux distributions, but nothing works.
This are the partitions, maybe it's... (12 Replies)
Hello:
NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
First of all, I'd like to preface this post by relaying that I have considerable experience with FreeBSD but I'm a Linux newb. I've been attempting to compile linux-2.6.29.3 from source and I'm having some problems and have a few newb questions...
a) First of all, my kernel won't boot, it fails... (0 Replies)
Our system is not booting up properly. It keeps going to this screen:
Enter Run Level (0-6, s or S):
I tried to hit all nos# 0-6 is just goes to hung state.
Tried s or S & it brings me to single user mode. I've checked the file systems & found out that all three had 98%. I tried to... (86 Replies)
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Discussion started by: gacanepa
0 Replies
LEARN ABOUT OPENSOLARIS
hal-device
hal-device(1M) System Administration Commands hal-device(1M)NAME
hal-device - manage HAL devices
SYNOPSIS
hal-device [-h] [--a udi | --r udi]
DESCRIPTION
The Hardware Abstraction Layer (HAL) provides a view of the various hardware attached to a system. The hal-device command enables you to
manage devices that conform to the HAL standard. Specifically, hal-device lets you add or remove a device to or from the HAL global device
list. Device properties are read from stdin in lshal(1M) syntax.
OPTIONS
The following options are supported:
-a, --add udi Add device specified by Universal Device Identifier udi to HAL's global device list.
-h Display usage information.
-r, --remove udi Remove device specified by Universal Device Identifier udi from HAL's global device list.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWhalr |
+-----------------------------+-----------------------------+
|Interface Stability |Volatile |
+-----------------------------+-----------------------------+
SEE ALSO hald(1M), attributes(5), hal(5)SunOS 5.11 25 Aug 2006 hal-device(1M)